VisualizationEspresso Pod Organizer SVG, Sloped Coffee Capsule Tray Laser Cut File, Coffee Sachet Holder DXF
A free laser cut file for a sloped espresso pod organizer with five cells: two wide ones at the front for capsules and three at the back for drip coffee bags and sugar sticks. The download has SVG and DXF for 3, 4, 5 and 6 mm plywood; the tray is 270 × 160 × 90 mm (10.63 × 6.30 × 3.54 in) and has 9 pieces. The front wall is lower with the sides sloping down to it, and it assembles with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 270 × 160 × 90 mm (10.63 × 6.30 × 3.54 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 880 × 262 mm
- Cut length
- 5.63 m
- Est. time, 10 W diode (3 mm)
- 18 min 46 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 49 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Use the file that fits your plywood and cut the cross divider first to check how it seats in the base.
- 02Cut the remaining pieces, 9 in total, on one 880 mm sheet or split over two.
- 03Fit the cross divider, then the single front divider and the two back dividers, and finish with the back wall, angled sides and short front.
- 04Sand the slopes smooth, oil the tray, and fill the front cells with pods and the back cells with sachets and sticks.
Two rows, five cells
Instead of splitting the box into equal lanes, this organizer uses two rows of different widths. A cross divider runs the full 270 mm length. Behind it, two dividers make three narrow cells; in front, a single divider makes two wide ones. In the photo the back row stands drip coffee sachets on the left and right with sugar sticks in the middle, and the front row holds capsules sorted by colour, gold and brown on one side and deep red on the other.
The back is 90 mm tall and the front is 54 mm, with the sides cut on a slope between them. The back cells keep their full height, so tall sachets do not flop over, while the front cells are shallow enough to pick a capsule without looking.
Cutting it out
The 3 mm layout measures 880 × 262 mm. Cutting time for the 3 mm file is about 18 min 46 s on a 10 W diode, about 7 min 49 s on a 40 W CO2 and about 3 min 45 s on a 100 W CO2. Lasers with a short bed can cut the base and cross divider on one sheet and the walls on a second.
Assemble from the inside out: cross divider into the base, then the front divider and the two back dividers, then the back wall, sloped sides and the low front. If the joints feel loose in your plywood, a little glue in each corner tightens everything up.
Sorting ideas
Two front cells make a simple rule easy: strong roasts on the left, mild or decaf on the right. Hosts can keep the back cells for tea or hot chocolate sachets. It suits anyone whose machine has a capsule drawer that is always too small, and filled with a few favourite blends it makes a thoughtful present.
Questions about this file
Which cells are best for capsules?
The two wide front cells. They are shallow, so pods are easy to see and pick out, while the three tall back cells hold sachets upright.
How tall are the two rows?
The back wall is 90 mm and the front wall 54 mm. The cross divider sits in between and keeps the two rows apart.
Can I cut this organizer on a 10 W diode?
Yes. 3 mm plywood goes through in one or two passes; 5 and 6 mm need more passes or a slower speed, so a CO2 is quicker for thick stock.
Is it possible to scale it for bigger pods?
You can enlarge it, but every slot must remain your plywood thickness. Fix the slot widths after scaling so the dividers fit snugly.
Can I personalise the organizer?
The file contains cut lines only. You can add a name or a coffee motif as your own engraving on the tall back wall or the sides.
Similar files



