Visualization6 Section Silverware Chest SVG, Sliding Lid Flatware Box Laser Cut File, 3x2 Cutlery Storage DXF
A free laser cut file for a cutlery box with a sliding lid and six compartments in three columns and two rows, 370 × 280 × 70 mm (14.57 × 11.02 × 2.76 in) outside. The download includes SVG and DXF for 3, 4, 5 and 6 mm plywood; its 11 pieces join with tabs and slots, and the lid slides in on two rails with no hinge or lock.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 370 × 280 × 70 mm (14.57 × 11.02 × 2.76 in)
- Parts
- 11
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,320 × 646 mm
- Cut length
- 11.80 m
- Est. time, 10 W diode (3 mm)
- 39 min 20 s
- Est. time, 40 W CO2 (3 mm)
- 16 min 24 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the SVG or DXF for your plywood thickness, then test one slot and check that the lid panel will clear the rails on a scrap cut.
- 02Cut the 11 pieces over two or three sheets, keeping the lid and both rails on the same sheet of plywood.
- 03Build the base, back, sides and lower front, slot in the crossing dividers, then fit the two stepped rails along the side walls with a little wood glue.
- 04Sand the lid until it slides smoothly, wax the rails, oil the box and slide the lid in over the six filled compartments.
A covered chest for the good cutlery
This is the box for a set that does not live in the everyday drawer. Two dividers run from front to back and one runs across, giving six compartments of about 12 cm by 13 cm. In the photo the front row holds dinner forks, tablespoons and table knives, and the back row keeps teaspoons, bamboo chopsticks and butter knives. The dividers are 60.7 mm tall, a little lower than the walls, so the lid passes over them.
The lid is a single flat panel that runs in two narrow stepped rails fitted along the side walls. The front wall is cut lower, at 63.7 mm, so the lid can be pushed in and pulled out from the front. Slide it halfway to take out a fork, or remove it completely when laying the table.
Cutting tips
The 3 mm file takes about 39 min 20 s on a 10 W diode, about 16 min 24 s on a 40 W CO2 and about 7 min 52 s on a 100 W CO2. The layout is 1320 × 646 mm, so most hobby machines need two or three sheets: the lid alone fills a 370 × 280 mm area. Cut the rails from the same sheet as the lid so their thickness matches.
Finishing and gift ideas
Sand the lid edges until it glides, then rub a little paste wax on the rails. A coat of oil or lacquer protects the inside from damp spoons. The flat lid is a natural spot for an engraved monogram or date that you add yourself.
- A wedding or anniversary gift with the couple's names on the lid
- A storage chest for inherited silver, kept in a sideboard
- A camping cutlery box that keeps dust off between trips
Questions about this file
What keeps the cutlery box lid in place?
It rests on two rails along the side walls and slides in from the lower front edge. There is no hinge or catch, so the box should be carried level.
Will a full 24-piece set fit inside?
Six bays of about 12 × 13 cm each hold six forks, six knives, six spoons and six teaspoons with room left for chopsticks or dessert forks. Serving pieces longer than 13 cm will not lie flat.
The lid sticks. What can I do?
Sand its long edges a little at a time and rub candle wax or paste wax on the rails. Humid kitchens can swell plywood, so a coat of lacquer on the lid helps it stay smooth.
Can I resize the box for a different set?
You can change the outer size in your editor, but keep the slot widths and rail height matched to your plywood. Scaling the whole drawing changes those too and the lid will no longer run cleanly.
Should I use 3 mm or thicker plywood?
3 mm makes a light box that cuts quickly on a diode. For a chest that holds heavy silver, 4 or 5 mm walls and a stiffer lid are worth the longer cut.
Similar files



