DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Low birch plywood cutlery insert with four bays holding forks, soup spoons, table knives and bamboo chopsticks, standing on a pale stone kitchen counter beside a vase of blue hydrangeas.Visualization
DW-104003 · UPDATED 11/17/2026

Shallow Cutlery Drawer Insert SVG, Four Bay Flatware Divider Laser Cut File, Low Wooden Utensil Box DXF

A low, four-bay cutlery insert sized to sit inside a shallow kitchen drawer or on the counter, with one cross divider and two short dividers making a 2 × 2 grid. It measures 300 × 280 × 60 mm (11.81 × 11.02 × 2.36 in), has 8 plywood pieces that join with tabs and slots, and is a free SVG and DXF download with separate files for 3, 4, 5 and 6 mm plywood.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
300 × 280 × 60 mm (11.81 × 11.02 × 2.36 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,180 × 352 mm
Cut length
6.39 m
Est. time, 10 W diode (3 mm)
21 min 18 s
Est. time, 40 W CO2 (3 mm)
8 min 52 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Open the folder for your plywood thickness and cut one wall corner first to see whether the tabs press in snugly.
  2. 02Cut the base, the four 60 mm walls, the full-width cross divider and the two short dividers.
  3. 03Join the walls around the base, slide in the cross divider, then drop one short divider into each half.
  4. 04Sand the top edges where hands reach in, wipe on a food-safe oil and lay the insert in the drawer.

Four bays at drawer height

At only 60 mm tall this is the flattest box in the cutlery set, so it slides under the rim of most kitchen drawers that a 70 mm tray would scrape. A full-width cross divider splits the box into a back half and a front half, and each half gets one short 141.5 mm divider, giving four bays of roughly equal size. In the photo the back pair holds dinner forks and soup spoons, the front pair holds table knives and a bundle of bamboo chopsticks. Swap in teaspoons, dessert forks or a corkscrew and bottle opener if your family uses those more.

Measure the inside of your drawer before cutting: you need a little over 300 mm across and 280 mm front to back. If the drawer is narrower, scale the design down in your software but keep the slot width equal to your sheet.

Cutting on a small bed

The 3 mm layout runs 1180 × 352 mm with a total cut line of 6388 mm. The 300 × 280 mm base is the only large panel; the walls and dividers are all 60 mm strips that nest easily on two or three smaller sheets. Expect about 21 min 18 s on a 10 W diode, about 8 min 52 s on a 40 W CO2 and about 4 min 16 s on a 100 W CO2, all for the 3 mm file. Thicker 5 or 6 mm birch makes a sturdier insert but takes extra passes on a diode.

Ideas for gifts and markets

  • Pair it with a boxed flatware set as a housewarming present.
  • Make a matching insert for the utensil drawer next to it and sell the two as a drawer kit.
  • Offer it in plain birch and in a dark oiled finish so buyers can match their cabinets.

Questions about this file

Will it fit a shallow drawer?

The walls are 60 mm high, so it suits drawers with about 65 mm of clear height inside. Check the depth too: the box is 280 mm from front to back.

Can I make the bays different sizes?

The two short dividers sit in fixed slots in the cross divider. To move them you would edit the slot positions in a vector editor before cutting.

Which thickness works best for a drawer insert?

3 or 4 mm keeps the insert light and leaves more room inside each bay. Go to 5 or 6 mm only if the box will be lifted out and carried often.

Is MDF a good choice here?

MDF cuts cleanly but swells if wet spoons go in. If you use it, seal every surface, including the slots, before assembly.

Should I glue the dividers?

The walls benefit from a little wood glue so the box stays square when you pull it out. The dividers can stay loose, which lets you lift them out for cleaning.

Similar files