DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Tall birch plywood tiered cutlery stand with three steps of three slots, each step holding forks, spoons and knives, chopsticks at the back, on a light counter.Visualization
DW-104062 · UPDATED 11/16/2026

Tiered Silverware Stand SVG, Restaurant Cutlery Station Laser Cut File, Nine Slot Utensil Display DXF

A tall tiered cutlery stand with three steps, each split by two dividers into three slots, nine slots in total, for a full self-service set of forks, spoons and knives. It measures 290 × 320 × 210 mm (11.42 × 12.60 × 8.27 in), is made of 15 plywood pieces with small engraved part numbers, assembles with tabs and slots, and is a free download in SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood.

Author
DXF World · 281 files
Formats
SVG, DXF
Outer size (W × D × H)
290 × 320 × 210 mm (11.42 × 12.60 × 8.27 in)
Parts
15
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,286 × 379 mm
Cut length
11.77 m
Est. time, 10 W diode (3 mm)
39 min 13 s
Est. time, 40 W CO2 (3 mm)
16 min 20 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the thickness folder that suits your plywood and cut one test slot to check that a shelf tab drops in without force.
  2. 02Cut the 15 numbered parts, keeping the two tall stepped sides together on one sheet.
  3. 03Assemble the frame on its side, fitting the front board, step boards, shelves and brace in number order, then add the second side and the six dividers.
  4. 04Sand the divider tops, apply a wipe-clean lacquer and set out forks, spoons and knives step by step.

A cutlery station in three tiers

Every step of this stand has three slots, so you can repeat the same pattern on each level: forks, spoons, knives. That is how the photo shows it, with dinner cutlery at the top, dessert sizes in the middle and small pieces at the front, plus a few chopsticks propped at the back. Guests read the stand from left to right and top to bottom, which keeps a queue moving at a buffet, a canteen counter, a hotel breakfast table or a food truck window. At home it turns a crowded drawer into an open display for a large family or a party.

Parts and assembly

The 15 pieces are two stepped side panels, a front board, two step boards, three shelves, a brace and six dividers. Each carries a small engraved number, which matters here because the six dividers come in two lengths. Build the frame lying on one side, add the shelves and risers in number order, close it with the second side, and only then drop in the dividers.

The 3 mm file is estimated at about 39 min 13 s on a 10 W diode, about 16 min 20 s on a 40 W CO2 and about 7 min 51 s on a 100 W CO2. In 3 mm the layout covers 1286 × 379 mm, so split it on a small bed with the tall sides on their own sheet. For a busy catering counter, 5 or 6 mm plywood makes a heavier stand that does not slide when people grab from it.

Branding and finishing

For a cafe or restaurant, add your logo to the front board as your own engraving. Seal with a hard-wearing lacquer that survives daily wiping, and make a matching napkin holder so the station looks like one set.

Questions about this file

Is this stand big enough for a restaurant buffet?

Each slot takes a generous handful of cutlery, so nine slots serve a busy breakfast. For larger events, cut two stands and place them at either end of the table.

Why do the dividers come in two sizes?

One of the three shelves is slightly deeper than the other two, so its pair of dividers is longer. The engraved numbers tell them apart.

Can I add my cafe logo?

Yes, engrave it on the front board or on a side panel as your own addition. The file itself only has cut lines and part numbers.

How do I keep it clean in a commercial kitchen?

Seal every surface, including slot edges, with a durable lacquer and wipe it daily. Do not put plywood in a dishwasher.

Is 6 mm plywood worth the extra cutting time?

For a busy station, yes: the stand gets heavier and steadier. Use the 6 mm file so the slots match, and expect several passes on a diode.

Similar files