DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood spice tray with three rows rising toward the back: cork-topped jars in front, silver-lidded jars in the middle and tall spice pouches at the back, on a kitchen counter by a white brick wall.Visualization
DW-101009 · UPDATED 11/20/2026

Three Row Spice Jar Tray SVG, Rising Divider Spice Organizer Laser Cut File, Sloped Spice Rack DXF

A free laser cut file for a three-row spice tray whose dividers rise toward the back, so jars in the front, middle and back rows all stay visible. It measures 330 × 200 × 100 mm (12.99 × 7.87 × 3.94 in), with a 40 mm front wall and sides that slope up to the 100 mm back. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood, and its 7 pieces join with tabs and slots.

Author
DXF World · 415 files
Formats
SVG, DXF
Outer size (W × D × H)
330 × 200 × 100 mm (12.99 × 7.87 × 3.94 in)
Parts
7
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,080 × 312 mm
Cut length
6.14 m
Est. time, 10 W diode (3 mm)
20 min 28 s
Est. time, 40 W CO2 (3 mm)
8 min 32 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Pick the file for your sheet thickness and test one tab of the back wall in a base slot before cutting everything.
  2. 02Cut the seven pieces, moving the base to a separate sheet if your bed is under 1080 mm wide.
  3. 03Push the back and the two sloped sides into the base, add the 40 mm front, then slot in the lower cross divider at the front and the taller one behind it.
  4. 04Sand and oil the tray, then fill the front row with the shortest jars and the back row with pouches or tall bottles.

Three rows, each one higher

Two long cross dividers run the full width and split the tray into three rows, front to back. Their heights climb in steps: the 40 mm front wall, then 57.4 mm, then 78.7 mm, then the 100 mm back. Every row shows a little more of what stands behind it, much like a tiered rack but without shelves to build. The front row is about 56 mm deep, the middle and back rows roughly 70 mm each.

In the photo the front row holds six small jars with cork stoppers (pink salt, paprika, coriander seed, turmeric and dried herbs), the middle row five jars with silver screw lids, and the back row a line of tall spice pouches standing upright. Because the rows have no side-to-side dividers, you can fit as many jars as the width allows, about five or six of this size per row.

Cutting notes

Seven parts fit on a 1080 × 312 mm layout in 3 mm. If your bed is smaller, put the base on its own sheet and the walls with the two dividers on a second. For the 3 mm file, expect about 20 min 28 s on a 10 W diode, about 8 min 32 s on a 40 W CO2 and about 4 min 06 s on a 100 W CO2. Thicker 5–6 mm sheet is slow on a diode, so use several passes or a CO2. The joints press together without glue; add a little along the base if you want it permanent.

Finishing touches

Round over the sloped top edges with fine sandpaper so hands do not catch on them. Hard wax oil brings out the birch grain and resists cooking splashes. For a gift, stock it with a starter set of a dozen spices; for a market table, sell it beside matching jar labels.

Questions about this file

Why are the rows not split into cells?

Each row stays open across the full 330 mm width, so jars of different diameters fit without wasting space. Add your own short dividers if you prefer fixed spots.

Which jars suit the front row?

Short jars work best at the front, since that row is about 56 mm deep. Taller bottles and pouches belong in the back row behind the 78.7 mm divider.

Could this spice tray be cut from MDF?

Yes, use the 3 mm file and seal the MDF afterwards, because raw MDF swells when it gets damp. Birch plywood stays lighter and copes better with moisture.

Is it safe to resize this tray?

The slots grow or shrink with the drawing and no longer match your plywood. Scale it, then set each slot back to the real material thickness.

Can I personalise the tray?

Add a name or a short phrase to the 100 mm back wall as an engraving in your laser software. The file itself contains cut lines only.

Similar files