Visualization2 Compartment Spice Box DXF, Open Spice Jar Organizer SVG, Simple Seasoning Packet Box Laser Cut File
A free laser cut file for an open spice box split into two compartments by one full-height divider, with jars on one side and seasoning packets on the other. It measures 260 × 220 × 100 mm (10.24 × 8.66 × 3.94 in) and is cut from only 6 plywood pieces that lock together with tabs and slots, which makes it the simplest build in the spice range. SVG and DXF files are provided for 3, 4, 5 and 6 mm plywood, each with slots sized for that sheet.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 220 × 100 mm (10.24 × 8.66 × 3.94 in)
- Parts
- 6
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 980 × 332 mm
- Cut length
- 5.65 m
- Est. time, 10 W diode (3 mm)
- 18 min 50 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 51 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Open the DXF or SVG for your sheet thickness and cut the divider slot area from scrap first to check the fit.
- 02Cut the six parts in one go, splitting the layout over two sheets on a small machine.
- 03Join the back and the two sides to the base, drop the divider into its slots, then close the box with the front wall.
- 04Sand the top edges smooth, apply a food-safe oil, and fill the left side with jars and the right with packets.
A deep box with two compartments
All four walls are a full 100 mm tall, and a single divider of the same height runs from front to back, so jars and packets stay upright even when the box is half empty. There is no lid and no sloped front: it is a plain, sturdy open box that slides into a cupboard or sits on the counter next to the stove.
In the photo the wider left compartment holds nine jars with brushed steel lids in three rows of three: dried herbs, peppercorns, chili, turmeric and seed mixes. The right compartment takes seasoning packets standing upright in rows one behind the other, basil at the back, a potato seasoning in the middle and a tomato blend at the front. At 22 cm deep, the box suits standard kitchen cabinets.
A good first project
With just six pieces (front, back, two sides, base and the divider) this is a quick cut and an easy first box for a new laser owner. Cutting time for the 3 mm file is about 18 min 50 s on a 10 W diode, about 7 min 51 s on a 40 W CO2 and about 3 min 46 s on a 100 W CO2. The 3 mm layout is 980 × 332 mm; on a 400 mm bed split it into two or three sheets with the base on its own. A diode cuts 3 mm in one or two passes, while 5 or 6 mm needs several slow passes or a CO2.
Selling ideas
Makers on Etsy can offer it plain or with a name engraved on the front. Bundle it with nine filled jars for a gift set, or make two and set them side by side in a wide drawer.
Questions about this file
What is the difference from the hinged and lidded versions?
This one is open with no lid, uses the fewest pieces and is the quickest to cut. Pick it for a cupboard shelf where dust is not an issue.
How tall can the spice jars be?
The walls are 100 mm tall, so jars up to about that height stay hidden behind the front, and taller jars simply show above the rim.
Is there a version for 6 mm plywood?
Yes, there is a 6 mm version with wider slots. It makes a very rigid box but takes several passes on a diode laser.
Is the box strong without glue?
Tab and slot joints hold it for normal use. Add wood glue along the base joints if you plan to carry it around full of glass jars.
Will grease from cooking stain the open box?
Seal all surfaces with a clear lacquer so grease and steam can be wiped off. Raw plywood absorbs oil stains quickly.
Similar files



