VisualizationFlip Top Napkin Box SVG, Pin Hinge Napkin Storage Laser Cut File, Square Wooden Napkin Box DXF
A free napkin box with a lid that flips open at the back on pins cut into the plywood, and one divider that makes a wide napkin section and a smaller side section. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 240 × 220 × 100 mm (9.45 × 8.66 × 3.94 in) and is built from 7 pieces with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 220 × 100 mm (9.45 × 8.66 × 3.94 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 940 × 336 mm
- Cut length
- 6.24 m
- Est. time, 10 W diode (3 mm)
- 20 min 48 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 40 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood and cut one side panel plus a scrap strip of lid to check that the pins turn freely.
- 02Cut all 7 pieces: base, front, back, two sides, the divider and the lid.
- 03Join the back, front and divider to the base, then fit the two sides while guiding the lid pins into the holes in their back ears.
- 04Sand the pins until the lid swings smoothly, finish the outside, and fill the box with napkins and straws.
The flip lid
The side panels rise into rounded ears at the back, and two short pins on the back edge of the lid turn in holes in those ears, so no metal parts are needed. Lift the front edge and the lid swings up and rests open; let go and it drops back flat to keep dust off the napkins. That makes it a tidy choice for a dining table that is not cleared every day, or for a counter near a window.
Inside the box
One divider running from front to back splits the nearly square interior into a wide section and a narrower one. In the photo the wide side holds a stack of white paper napkins, and the narrow side is packed with metal straws, wooden toothpicks and a few cork coasters. The photo shows that side split into small rows; the file has the single divider, so add offcut strips with glue if you want the same. The 100 mm walls take a full napkin pack standing loose.
Cutting and finishing
All pieces fit a 940 × 336 mm layout for 3 mm plywood, so a mid-size bed can take it in two runs. The estimated time for the 3 mm file is about 20 min 48 s on a 10 W diode, about 8 min 40 s on a 40 W CO2 and about 4 min 10 s on a 100 W CO2. For 5 or 6 mm, plan several diode passes or use a CO2 tube. Leave the lid unglued so it can pivot, sand the pin areas smooth, then oil or lacquer the box. It makes a neat wedding or housewarming gift with a name engraved on the lid.
Questions about this file
How does the lid pivot without hinges?
Two short pins on the back edge of the lid sit in holes in the rounded ears of the side panels, so the lid turns on wood alone.
What if the lid feels stiff?
Sand the pins lightly and rub a little candle wax on them. Plywood can vary from its stated thickness, which tightens the fit.
Can I scale it to fit bigger napkins?
You can enlarge it, but the slots and pins must stay sized to your sheet thickness, so adjust them after scaling.
Should I glue the box?
Glue the base and wall joints if you like, but keep glue away from the lid and its pins so it still opens.
Can I add a monogram?
Yes. Add initials or a pattern to the lid in your laser software and engrave it before the cut; the file itself only has cut lines.
Similar files



