VisualizationCondiment Caddy SVG, Two Row Oil and Sauce Organizer Laser Cut File, Wooden Kitchen Counter Tray DXF
A long, low condiment caddy with six bays in two rows: three at the back for oil and vinegar bottles and three in front for sauce and mustard jars. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the caddy measures 330 × 160 × 80 mm (12.99 × 6.30 × 3.15 in), is made of 10 pieces and has a front that drops to 56 mm, with tabs and slots holding it together. It is a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 330 × 160 × 80 mm (12.99 × 6.30 × 3.15 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,334 × 252 mm
- Cut length
- 6.43 m
- Est. time, 10 W diode (3 mm)
- 21 min 26 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 56 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the SVG or DXF for your plywood thickness and cut one short divider first to check that its tabs fit the base slots snugly.
- 02Split the 1334 mm layout across two or three sheets if your bed is smaller, then cut all ten pieces.
- 03Seat the back and both sides in the base, add the low front, then slot in the long cross divider and the four short dividers.
- 04Sand, oil or lacquer the caddy, then load bottles in the tall back bays and jars in the lower front bays.
Two rows, six bays
A single cross divider runs the full 330 mm length and splits the caddy into a back row and a front row. Each row gets three bays from two short dividers. The back row keeps the full 80 mm height, which steadies square oil bottles; in the photo it holds olive oil, a dark balsamic and a bottle of oil with a rosemary sprig. The front row is lower: its dividers and the cross divider are 67.8 mm tall and the front wall is only 56 mm, so the jars there (tomato sauce, grainy mustard, a dark chutney) show their lids from across the kitchen.
At 160 mm deep the caddy sits comfortably on a counter next to the hob, and the 330 mm length suits most cabinet shelves too, so the whole set slides away when you need the space.
Cutting and putting it together
All ten pieces are laid out on a strip 1334 mm long. That is longer than most hobby lasers, so split the parts across two or three sheets: the base and back on one, the walls and dividers on the others. A 10 W diode handles 3 mm plywood in one or two passes and takes about 21 min 26 s for the 3 mm file; a 40 W CO2 needs about 8 min 56 s. For 5 or 6 mm plywood plan extra passes on a diode, or use a CO2.
Fit the back and the two sides into the base first, then add the low front. Drop in the long cross divider, followed by the four short dividers. The tab-and-slot joints hold without glue, though a drop of wood glue on each joint makes the caddy permanent.
Finishing for the kitchen
Sand the edges lightly and wipe on food-safe oil or a clear lacquer so oil drips wipe off. Two or three of these caddies make a neat matching set for a market stall, or fill one with small bottles of homemade dressing as a gift for a friend who cooks.
Questions about this file
What fits in the back bays?
Each back bay is about a third of the 330 mm length wide, which suits slim square or round oil and vinegar bottles. Measure your widest bottle against the part sizes before cutting.
Can I make it longer to hold four bottles per row?
Not by simple scaling, because stretching the file also stretches the slots, and they must stay equal to your plywood thickness. Lengthen the walls and add a divider in a vector editor instead.
Will oil soak into the plywood?
Raw plywood absorbs oil and stains. A coat of clear lacquer or a hard-wax oil seals the bays so drips wipe off.
Which plywood thickness should I use for glass bottles?
3 mm keeps the caddy light and quick to cut, while 4 mm feels sturdier under full glass bottles. The 5 and 6 mm files are easiest on a CO2 laser.
Is there room on the front for an engraved name?
The file has cut lines only, but the 330 mm front is a good place to add your own engraving, such as a family name or a shop logo, before cutting.
Similar files



