VisualizationTea Box With Lid SVG, Lift Off Lid Tea Storage Laser Cut File, Three Section Tea Bag Box DXF, Wooden Tea Case
A free tea storage box with a separate lid that lifts off and sits on top, and 3 sections inside from left to right for tea bags and tins. It is offered as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood, measures 260 × 160 × 80 mm (10.24 × 6.30 × 3.15 in) and assembles from 8 pieces with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 160 × 80 mm (10.24 × 6.30 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 860 × 252 mm
- Cut length
- 7.58 m
- Est. time, 10 W diode (3 mm)
- 25 min 16 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 32 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the version for your plywood thickness and cut a tab and slot on scrap to confirm the joint is snug.
- 02Cut the base, four walls, two dividers and the separate lid panel.
- 03Join the walls to the base, slide the dividers into place, and set the lid on top to make sure it rests evenly.
- 04Sand and finish the box and lid, decorate the lid if you like, then sort your teas into the three sections.
Box and lid
The lid is a single flat panel the same size as the box footprint, 260 by 160 mm, that rests on the walls. Lift it off, lean it against the wall behind the box as in the photo, and everything is in reach; put it back and the tea is covered. There are no moving parts, which makes it the simplest closed box to build and to clean.
Three sections, three kinds of tea
In the photo the left section carries mixed wrapped bags in white, red, yellow and green, the middle one holds two windowed tins of dried flowers and rosebuds, and the right section is lined with white sachets printed with leaves. The dividers are 77 mm tall, nearly the full wall height, so the lid sits almost on them and the rows stay upright.
Cutting notes
The file nests on an 860 × 252 mm sheet. On a 400 mm bed, cut the lid with the base and the long walls on a second sheet. For the 3 mm file allow about 25 min 16 s on a 10 W diode, about 10 min 32 s on a 40 W CO2 and about 5 min 03 s on a 100 W CO2. Go for 3 or 4 mm on a diode; 5 and 6 mm cut better on a CO2 or with several passes.
Tab-and-slot joints hold the walls without glue. Add glue along the base joints if the box will travel. Sand the lid edges so it drops on and off smoothly, then finish everything with oil or water-based lacquer.
This lid is a good surface for decoration: engrave a pattern, the word tea in a nice font, or a shop logo for a counter box. Sold as a gift box filled with samplers, it makes a tidy present for birthdays or the holidays.
Questions about this file
Does the lid stay in place when I carry the box?
It rests on top, so carry the box level or hold the lid with your thumbs. For travel, tie it with a ribbon or a band.
Can I use one box for tea bags and loose leaf at the same time?
Yes. Put wrapped bags in the outer sections and keep loose leaf in small tins in the middle, as the photo shows.
Which thickness looks best for a gift box?
Four or five millimetre birch gives a solid, chunky look. Three millimetre is lighter and cuts faster on a diode.
Will 3 mm MDF work with the 3 mm file?
It will, provided your MDF really is 3 mm. Measure the sheet, because some boards run thicker and the tabs will then be too tight.
Can I stack two of these boxes?
The flat lid takes a second box on top without trouble, which is handy for a pantry shelf.
Similar files



