DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood long spice box with a sliding lid covering the right end and six compartments: small capped spice jars on the left and seasoning sachets in the middle, on a terracotta-tiled kitchen counter.Visualization
DW-101024 · UPDATED 11/19/2026

Sliding Lid Box SVG, Long Wooden Spice Box Laser Cut File, Six Compartment Seasoning Storage DXF

A free laser cut file for a long spice box with a sliding lid that runs on two rails, holding six compartments in two rows of three. The download contains SVG and DXF for 3, 4, 5 and 6 mm plywood; the box is 370 × 160 × 80 mm (14.57 × 6.30 × 3.15 in) and is made of 11 pieces that fit together with tabs and slots, with no hinges or hardware.

Author
DXF World · 368 files
Formats
SVG, DXF
Outer size (W × D × H)
370 × 160 × 80 mm (14.57 × 6.30 × 3.15 in)
Parts
11
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,454 × 332 mm
Cut length
9.35 m
Est. time, 10 W diode (3 mm)
31 min 09 s
Est. time, 40 W CO2 (3 mm)
12 min 59 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the SVG or DXF for your sheet thickness and cut one side wall plus a rail first to check the slot fit.
  2. 02Cut all 11 pieces, spreading the 1454 mm layout over two or three sheets on a smaller bed.
  3. 03Assemble base, back, sides and the lower front, set the long divider and the two short dividers inside, then fix the two rails along the inside of the side walls.
  4. 04Slide the lid in, sand any tight spots, apply a thin finish and fill the six cells.

Six cells under one sliding lid

A long divider runs the full length and splits the box into a front and a back row; two short dividers cross it, giving three columns. That makes six cells of about the same size, each a little under 12 cm wide. In the photo the left pair holds small capped jars (peppercorns, chilli, oregano, turmeric, paprika, mixed herbs) and the middle pair keeps foil sachets and herb packets standing up. The right end is hidden under the lid.

The lid is a flat 363.4 × 159.7 mm panel. Two rails, each 157 mm long, sit along the inside of the side walls and carry it, and the front wall is a little lower than the back (73.7 mm against 80 mm), which leaves room for the lid to pass. There is no hinge and no catch; the lid simply slides, so leave it a touch loose.

Before you cut

This is the longest layout in the spice set: 1454 × 332 mm for the 3 mm version. Few hobby lasers take that in one go, so split it, for example lid and base on one sheet, walls on a second, dividers and rails on a third. The 3 mm file takes about 31 min 09 s on a 10 W diode, about 12 min 59 s on a 40 W CO2 and about 6 min 14 s on a 100 W CO2. In 5 or 6 mm a diode needs several passes.

Lid fit and finish

Once the rails are in place, test the lid before any finish goes on. If it sticks, sand its edges rather than the rails. Seal it with a thin coat, since thick varnish can make a sliding lid bind. An engraved herb pattern or a family name on the lid, added yourself, turns it into a wedding or housewarming present, and a spice shop can put its logo there.

Questions about this file

How does the lid stay on this box?

It rests on two rails inside the side walls and slides in and out. There is no lock, so the box is meant to stand on a counter or shelf rather than be carried upside down.

What fits in each of the six cells?

Two or three small spice jars side by side, or a stack of flat seasoning sachets. Pick jars shorter than the walls so the lid can close over them.

Is such a long box hard to cut on a diode laser?

Not hard, only slow, and the parts must be rearranged because the layout is 1454 mm long. Cut the lid last so it does not pick up scorch marks while you handle the other sheets.

Which plywood thickness slides best?

3 or 4 mm birch gives a light lid that glides easily. A 6 mm lid is sturdier but heavier, and the rails then need a smooth sanding.

Can I make the lid from acrylic?

Yes, if you cut it from acrylic of the same thickness as the plywood file you chose, so it still fits between the rails. A clear lid shows the spices without opening the box.

Similar files