DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood tea box with its flat lid leaning behind, four sections holding green sachets, four tins of loose tea and paper tea bags on a kitchen tableVisualization
DW-102043 · UPDATED 11/19/2026

Tea Box With Lid SVG, Lift Off Lid Tea Organizer Laser Cut File, Four Section Wooden Tea Box DXF

A four-compartment tea box with a separate flat lid that sits on top and lifts straight off, with the inside split two by two by crossed dividers. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 320 × 160 × 100 mm (12.60 × 6.30 × 3.94 in) and is cut as 8 pieces that assemble with tabs and slots.

Author
DXF World · 368 files
Formats
SVG, DXF
Outer size (W × D × H)
320 × 160 × 100 mm (12.60 × 6.30 × 3.94 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,128 × 272 mm
Cut length
9.35 m
Est. time, 10 W diode (3 mm)
31 min 10 s
Est. time, 40 W CO2 (3 mm)
12 min 59 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Open the SVG or DXF for your plywood and cut a single tab-and-slot pair from scrap to confirm the kerf before the real run.
  2. 02Cut the 8 pieces, putting the lid and base on a second sheet if your bed is shorter than the 1128 mm layout.
  3. 03Build the walls around the base, cross the long and short divider and push them in, then set the lid on top to check it sits flat.
  4. 04Sand the rim and lid edges, oil or paint, and load the four sections with tins and bags.

Lid off, tea out

The lid is a single 320 × 160 mm panel that rests on the walls, so there is nothing to slide or pivot: lift it, take a bag, put it back. That makes this the easiest of the lidded tea boxes to cut and assemble, and the lid doubles as a small tray while the box is open. Under it, two dividers cross to form four sections of about 15 × 7.5 cm. In the photo the back row holds green tea sachets and two tins of loose leaf, the front row two more tins and a line of plain paper bags. The dividers stand about 88 mm tall, just below the rim, so the lid lies flat.

Sheet layout and cutting time

You cut 8 pieces: front, back, two sides, base, a long divider, a short divider and the lid. The layout is about 1128 × 272 mm for the 3 mm version, so smaller beds will need the lid and base cut as a separate job. Expect about 31 min 10 s on a 10 W diode, about 12 min 59 s on a 40 W CO2 and about 6 min 14 s on a 100 W CO2 for the 3 mm file. For 5 or 6 mm plywood a 10 W diode needs two or more passes per line.

Building and finishing

Join the four walls around the base, then interlock the two dividers and press them down. A bead of glue along the base joints is optional. Check that the lid sits evenly and sand the top edges of the walls if it rocks. Finish inside and out with a clear food-safe oil, or paint the lid only for a two-tone look.

Selling and gift ideas: a teacher's gift with four teas inside, a matching pair for tea and coffee pods, or a branded lid for a small cafe's retail shelf.

Questions about this file

Will the loose lid fall off if I move the tea box?

It rests on the walls without a catch, so hold the box from below or with a hand on the lid when moving it.

What sizes go inside each bay?

Each bay is about 15 × 7.5 cm with 88 mm dividers, which takes upright tea bags or two small round tins.

Could I shrink this tea box to fit a drawer?

Yes, scale the whole drawing, then correct every slot back to your actual plywood thickness so the joints still fit.

Is 3 mm or 5 mm plywood better for this box?

3 mm gives a light box for sachets; 4 or 5 mm feels more solid and suits a box that will hold full tins.

How do I protect it near a kettle?

Seal all surfaces, including the cut edges, with lacquer or several coats of oil so steam does not raise the grain.

Similar files