VisualizationCoffee Pod Chest SVG, Sliding Lid Coffee Box Laser Cut File, Eight Compartment Capsule Storage DXF
A free laser cut file for a long coffee pod chest with a sliding lid and eight compartments set out in four columns and two rows. It includes SVG and DXF for 3, 4, 5 and 6 mm plywood; the chest is 370 × 160 × 80 mm (14.57 × 6.30 × 3.15 in) and is made of 12 pieces, including the lid and two rails. The lid slides in along the rails, with no hinge or lock, and the box assembles with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 370 × 160 × 80 mm (14.57 × 6.30 × 3.15 in)
- Parts
- 12
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,454 × 406 mm
- Cut length
- 10.03 m
- Est. time, 10 W diode (3 mm)
- 33 min 26 s
- Est. time, 40 W CO2 (3 mm)
- 13 min 56 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Take the file for your plywood thickness and test-cut one cross-halving slot on scrap before the long run.
- 02Cut all 12 parts over as many sheets as your bed needs, keeping the base, the 364 mm divider and the lid whole.
- 03Interlock the dividers, seat them in the base, add the walls with the lower front, fit the two rails and slide in the lid.
- 04Wax the lid edges, finish the chest with oil or lacquer, and fill the eight cells by type.
Eight cells for a variety pack
Variety packs are the reason this chest exists. A long divider runs the full 364 mm inside length and three short dividers cross it, giving four columns of two cells each, eight in total. In the photo the open end shows capsules in the first column, tea or coffee sachets in the second and two kinds of sticks in the third, with the fourth column hidden under the lid. That leaves space for decaf, hot chocolate or stirrers without mixing anything.
The 363 mm lid covers the whole top when closed, and pushed back halfway it turns the chest into an open tray for the cells you use most. The dividers are 70.7 mm tall, below the 80 mm walls, so the lid passes over them.
A long layout
This is the biggest piece in the coffee set to cut. The 3 mm layout is 1454 × 406 mm, and the 6 mm one is arranged differently at 1499 × 329 mm. Unless you have a large CO2 bed, plan on three sheets, keeping the long base, long divider and lid each in one piece. Cutting time for the 3 mm file is about 33 min 26 s on a 10 W diode, about 13 min 56 s on a 40 W CO2 and about 6 min 41 s on a 100 W CO2.
Interlock the long divider with the three short ones before setting them into the base. Add the walls, fit both rails, and slide the lid in to check that it runs the full length before you glue anything.
Where it works best
It suits an office break room, a hotel minibar shelf or a long kitchen windowsill. A plain lid this long is a good spot for a row of engraved coffee beans or a business logo, added by you before cutting.
Questions about this file
What fits in each of the eight cells?
Each cell is roughly 85 mm wide and 75 mm from front to back, enough for a small stack of espresso capsules, a row of sachets or a bundle of sugar sticks.
Does the lid lift off or slide?
It slides along two rails and can be pulled right out for cleaning. There is no hinge or catch on this chest.
My laser bed is only 400 mm wide. Can I still cut it?
Yes. The longest pieces are about 370 mm, so each one fits, but the whole layout has to be spread over several sheets.
Can I cut the chest in acrylic?
A CO2 laser cuts acrylic cleanly; pick the file closest to the sheet's real thickness. A tinted acrylic lid over a plywood box looks good on a café counter.
Can I keep it near the sink?
Seal every surface, including the cut edges, with clear lacquer. Plywood edges soak up water fastest, so give them a second coat.
Similar files



