DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood box with straight sides and five equal sections holding hot sauce, soy sauce, olive oil, red wine vinegar and a swing-top oil bottle on a wooden kitchen worktopVisualization
DW-106020 · UPDATED 11/19/2026

Condiment Bottle Organizer SVG, Five Section Sauce Box Laser Cut File, Kitchen Oil Bottle Holder DXF

This is an open, straight-walled box that keeps five bottles of sauce, oil or vinegar upright in five equal sections divided from front to back. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood and makes a 380 × 220 × 80 mm (14.96 × 8.66 × 3.15 in) box from 9 pieces with tab-and-slot joints.

Author
DXF World · 368 files
Formats
SVG, DXF
Outer size (W × D × H)
380 × 220 × 80 mm (14.96 × 8.66 × 3.15 in)
Parts
9
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,284 × 312 mm
Cut length
9.48 m
Est. time, 10 W diode (3 mm)
31 min 36 s
Est. time, 40 W CO2 (3 mm)
13 min 10 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Select the SVG or DXF for your sheet thickness and trial-fit one tab in a slot cut from scrap.
  2. 02Cut the base, the long front and back, two short ends and four dividers, on one sheet or two depending on your bed.
  3. 03Build the four walls around the base, then press the dividers into their slots one at a time from one end to the other.
  4. 04Sand all edges, apply a clear finish, let it cure and set one bottle in each of the five bays.

Layout and what it holds

All four walls are the same 80 mm height, and four full-height dividers run the 220 mm depth, giving five bays of equal width. Because the walls are low compared with most bottles, the box works as a stable base that stops bottles sliding around a cupboard shelf or tipping in a drawer. The photo shows, from left, a small hot sauce, soy sauce, a square olive oil bottle, red wine vinegar and a swing-top bottle of oil. The extra depth makes it a handy fit for a pantry shelf, a fridge door or the back of a deep worktop.

Cut time and sheet size

The nine pieces are laid out on 1284 × 312 mm, so on a smaller machine cut the base and the long front and back first, then the two ends and four dividers on a second sheet. Cutting takes about 31 min 36 s on a 10 W diode, about 13 min 10 s on a 40 W CO2 and about 6 min 19 s on a 100 W CO2, all for the 3 mm file. A diode copes with 3 mm in one or two passes but struggles with 6 mm; use a CO2 or slow multi-pass settings for thicker sheet.

Make it a set

This straight box pairs well with a sloped caddy or a spice tray cut from the same plywood, so a whole cupboard matches. Seal it with clear lacquer or a food-safe oil after sanding, and add wood glue at the corners if it will be moved often. Sell it filled with five local sauces at a market stall, or give it to a barbecue fan with their favourite hot sauces in each bay.

Questions about this file

How wide is each section?

The 380 mm length is shared by five equal bays, so each fits one standard sauce or oil bottle with a little room to spare.

Can I put it inside the fridge?

Yes, once it is sealed with a waterproof lacquer. Wipe off condensation so the plywood does not stay damp.

Which thickness should I cut?

3 mm keeps it light and quick on a diode; 5 or 6 mm makes a heavier box for a shop counter or a busy kitchen.

Is glue needed to hold the five bays together?

No, the tabs lock the walls together on their own. Glue only matters if the box will be carried around full.

Can I change the box to hold taller bottles?

You can stretch the walls in height in your editor without touching the slot widths. Avoid uniform scaling, which would make the slots too wide or too narrow for your plywood.

Similar files