DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood box with a sliding lid half open over eight compartments holding napkins, cork and printed coasters, toothpicks and metal and green straws on a marble counterVisualization
DW-105028 · UPDATED 11/21/2026

Sliding Lid Box SVG, Eight Compartment Table Setting Box Laser Cut File, Covered Napkin and Straw Organizer DXF

A free covered table setting box with a sliding lid and eight compartments in two rows of four, for napkins, coasters, toothpicks and straws. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 340 × 200 × 90 mm (13.39 × 7.87 × 3.54 in) and is made from 12 pieces with tabs and slots, and the lid slides in on two rails.

Author
DXF World · 530 files
Formats
SVG, DXF
Outer size (W × D × H)
340 × 200 × 90 mm (13.39 × 7.87 × 3.54 in)
Parts
12
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,280 × 506 mm
Cut length
10.87 m
Est. time, 10 W diode (3 mm)
36 min 14 s
Est. time, 40 W CO2 (3 mm)
15 min 06 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the file for your plywood and test a rail with a scrap strip of lid so you know it will slide.
  2. 02Cut the 12 pieces over two or three runs, keeping the lid and base together in the first.
  3. 03Assemble base, back and sides, glue the rails inside the side walls, build the divider grid, then add the lower front.
  4. 04Sand and wax the lid edges, finish the box, and fill all eight compartments.

Eight compartments under one lid

One long divider and three short dividers cross to form a grid of two rows by four, each cell roughly 80 mm wide and 98 mm deep when cut from 3 mm plywood. That is enough to give every table item its own place. In the photo the back row holds leaf-print napkins, cork coasters, a glass of toothpicks and metal straws, while the front row has plain white napkins, printed coasters, more toothpicks and green straws. The dividers stand a little below the walls so the lid passes over them.

The sliding lid

Two rails fixed inside the side walls carry the lid, and the front wall is slightly lower so the lid slides out over it. Slide it back halfway to reach the front row, or remove it entirely when guests arrive. With no hinge and no lock, there is nothing to snag or break, but keep the box level when you carry it.

Cutting and finishing

This layout is wider than the others in the set: 1280 × 506 mm for 3 mm plywood, so cut the base and lid in one run and the walls, rails and dividers in a second or third. The estimated time for the 3 mm file is about 36 min 14 s on a 10 W diode, about 15 min 06 s on a 40 W CO2 and about 7 min 15 s on a 100 W CO2. Thicker 5 and 6 mm sheets call for extra diode passes or a CO2 laser. Sand and wax the lid edges, then seal the box with oil or lacquer. Ideas: a restaurant table box branded on the lid, a gift for a new home with matching napkins, or a tea and coffee pod box for an office kitchen.

Questions about this file

How large is each compartment?

With 3 mm plywood each cell is about 80 × 98 mm inside, slightly less with thicker sheets. Cocktail napkins, 4 inch coasters and a toothpick glass all fit.

How is this different from a lift-off lid box?

The lid stays captured in its rails and slides open, so it never needs a spot on the table while the box is in use.

Can I leave out a divider?

Yes. Skipping one short divider makes a double-width cell for cutlery or long napkins, and the grid still holds together.

Which thickness is easiest to slide?

The 3 and 4 mm files give the lightest lid. With 6 mm, sand the lid edges carefully and wax them for a smooth run.

Can I brand the lid for my restaurant?

Yes. Place your logo on the lid in your laser software and engrave it before cutting; the file itself contains only cut lines.

Similar files