VisualizationCutlery Chest SVG, Six Compartment Flatware Box With Lid Laser Cut File, Wooden Silverware Storage Case DXF
A cutlery chest with a separate lift-off lid and six sections in two rows of three, sized for a full table set. It measures 350 × 280 × 70 mm (13.78 × 11.02 × 2.76 in), is built from 9 plywood pieces with tab and slot joints, and is a free SVG and DXF download with separate files for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 350 × 280 × 70 mm (13.78 × 11.02 × 2.76 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,280 × 646 mm
- Cut length
- 12.04 m
- Est. time, 10 W diode (3 mm)
- 40 min 08 s
- Est. time, 40 W CO2 (3 mm)
- 16 min 43 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the files for your plywood thickness and cut one corner joint as a test before using a full sheet.
- 02Cut the base and lid panels first, then the four 70 mm walls, the two long dividers and the cross divider.
- 03Build the walls around the base, interlock the three dividers into a six-section grid and lower it into the chest.
- 04Sand the lid edges smooth, finish everything with oil or lacquer and sort a full table set into the six sections.
Room for a complete table set
Two long dividers and one cross divider split the inside into six sections, three at the back and three at the front. The photo shows a sensible fill: dinner forks, soup spoons and table knives in the back row, dessert forks, teaspoons and chopsticks in the front row. With 70 mm walls the sections are deep enough that heavy pieces stack two or three high without poking above the rim.
The lid is a flat 350 × 280 mm panel, the same footprint as the box, and simply rests on top of the walls. Lift it off and lean it behind the chest while you set the table. Because nothing is attached, the lid can double as a small serving board or a trivet when the chest is open.
Before you cut
The layout for 3 mm plywood is 1280 × 646 mm, with base and lid taking most of it. On a 400 mm bed, cut base and lid on separate sheets and the walls and dividers on a third. The time for the 3 mm file is about 40 min 08 s on a 10 W diode, about 16 min 43 s on a 40 W CO2 and about 8 min 02 s on a 100 W CO2. A 10 W diode handles 3 or 4 mm in one or two passes; for 6 mm, expect three passes or use a CO2.
Slot the long and cross dividers into each other on the bench, then drop the grid into the walls. A spot of glue at each corner keeps the chest square when it is carried full.
Gift and shop ideas
- Fill it with a new cutlery set as a wedding or housewarming present.
- Engrave a family name across the lid.
- Offer it beside matching napkin rings at a holiday market.
Questions about this file
What keeps the loose lid in place?
It is a flat panel the same size as the box that rests on the walls by its own weight. Carry the chest level, or tie a ribbon around it for gifting.
Will a set for six people fit?
Yes. Each of the six sections takes one type of piece for six place settings, and the 70 mm depth leaves room for a second set on top.
Can I cut the lid from a different material?
Any flat 3 to 6 mm sheet works for the lid since it has no slots. Smoked or clear acrylic shows off the cutlery inside.
Does the chest need glue?
Tabs and slots hold it for light use. Glue the four corners if the chest will be lifted and moved while full.
What finish suits a cutlery chest?
Hard wax oil gives a warm look and resists fingerprints. Lacquer the inside too if you store cutlery that is not fully dry.
Similar files



