DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood box with its lid leaning behind it on a linen runner, showing four compartments with napkins, cork coasters, a glass of toothpicks and steel straws.Visualization
DW-105043 · UPDATED 11/19/2026

Wooden Box with Lid SVG, Napkin Storage Box Laser Cut File, Four Compartment Kitchen Box DXF

This free file makes a napkin storage box with a separate lift-off lid, measuring 320 × 160 × 100 mm (12.60 × 6.30 × 3.94 in) and split into four compartments. It is cut as 8 plywood pieces that assemble with tabs and slots, and comes as SVG and DXF for 3, 4, 5 and 6 mm plywood.

Author
DXF World · 368 files
Formats
SVG, DXF
Outer size (W × D × H)
320 × 160 × 100 mm (12.60 × 6.30 × 3.94 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,128 × 272 mm
Cut length
9.44 m
Est. time, 10 W diode (3 mm)
31 min 27 s
Est. time, 40 W CO2 (3 mm)
13 min 06 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Use the file that matches your plywood thickness and run a single slot test on scrap first.
  2. 02Cut the 8 pieces, including the flat lid and the two crossing dividers.
  3. 03Assemble the four walls on the base, slot the two dividers together and lower them in, then place the lid on top.
  4. 04Sand the lid edges, apply oil or lacquer to all parts, and load the compartments.

Layout and lid

The walls are all 100 mm high and the lid is a flat 320 × 160 mm panel that sits on top; lift it off, set it aside, and the whole box is open. Inside, a long divider and a short one cross to make two rows of two. The photo shows a stack of napkins and a pile of cork coasters at the back, a square glass of toothpicks and a handful of steel straws at the front. It is a calm, plain box that fits on a shelf or in a sideboard cupboard as well as on the table.

Cutting the pieces

The file has eight parts: front, back, two ends, base, two dividers and the lid. The 3 mm file runs about 31 min 27 s on a 10 W diode, about 13 min 06 s on a 40 W CO2 and about 6 min 17 s on a 100 W CO2. Its 3 mm layout is 1128 × 272 mm; on a 400 mm wide bed, cut the lid and base in one job and the four walls with the dividers in another. A diode cuts 3 mm in one or two passes, while 5 and 6 mm need slower speed and extra passes.

Finishing and uses

A little glue in the base joints makes it permanent, but the lid stays loose. Sand the lid edges so it lifts off cleanly, and finish everything with oil or clear lacquer. Uses beyond napkins: a tea and sugar packet box for an office kitchen, a box for party straws and picks, or a gift box for a set of cloth napkins with a pattern engraved on the lid. Sellers can offer it alongside open caddies from the same range.

Questions about this file

Is the lid attached?

No, it is a separate panel that rests on the walls, so you lift it off and put it back.

What can I store besides napkins?

Coasters, straws, toothpicks, sugar packets or tea bags all fit the four compartments.

Can I resize the lidded box to fit inside a sideboard drawer?

Yes, scale the outline, then reset every slot width to your board thickness, otherwise the joints will not fit.

Is MDF a good choice?

MDF cuts well and paints nicely, but it swells with moisture, so seal it fully if the box stays in a kitchen.

How do I decorate the lid?

Engrave a name, a monogram or a pattern on the lid in a separate engrave step. The download itself contains only cut lines.

Similar files