VisualizationNapkin Organizer SVG, Four Compartment Table Caddy Laser Cut File, Wooden Condiment Station Box DXF
This free file cuts an open four-compartment napkin organizer measuring 320 × 180 × 100 mm (12.60 × 7.09 × 3.94 in). Two full-size dividers cross in the middle to form a 2 × 2 grid, and all 7 pieces assemble with tabs and slots; the download includes SVG and DXF versions for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 180 × 100 mm (12.60 × 7.09 × 3.94 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,020 × 292 mm
- Cut length
- 7.39 m
- Est. time, 10 W diode (3 mm)
- 24 min 38 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 16 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the thickness version that matches your plywood and test-cut a slot to check the fit.
- 02Cut the 7 pieces: front, back, two ends, base, the long divider and the short divider.
- 03Build the outer walls on the base, then join the two dividers at their centre slots and lower the cross into the box.
- 04Sand the top edges, apply oil or lacquer, and load napkins, straws, coasters and picks into the four squares.
Four equal compartments
All four walls are 100 mm tall, and two dividers of the same height cross in the centre: one runs the full 320 mm length, the other the 180 mm depth. They are slotted halfway so they lock into each other like an egg crate, giving four compartments of the same size. In the photo the back pair holds a block of folded napkins and a bunch of gold and steel straws, and the front pair holds cork coasters and a jar of toothpicks. Because every wall is the same height, the box looks tidy from any side, which suits a kitchen island or a buffet table that guests walk around.
Cutting notes
Only seven parts: front, back, two ends, base and the two crossing dividers. Expect about 24 min 38 s on a 10 W diode for the 3 mm file, about 10 min 16 s on a 40 W CO2 and about 4 min 56 s on a 100 W CO2. The 3 mm layout spans 1020 × 292 mm, longer than most hobby beds, so split it: base and long divider on one sheet, the remaining walls and the short divider on a second. A cross-slot test on scrap is worth doing first, since both dividers must slide together without forcing.
Finishing and selling
Glue is optional; the grid stiffens the box once it is assembled. Round the top edges with fine sandpaper, then seal with food-safe oil or water-based lacquer. Offer it as a condiment and napkin station for small cafes, a self-serve corner at weddings, or a craft-fair gift filled with napkins and straws. A version in 6 mm plywood feels solid enough for a market stall that sees daily use.
Questions about this file
Are the four compartments the same size?
Yes, the dividers cross at the centre, so each square is a quarter of the box. That makes it easy to swap what goes where.
How do the dividers stay in place?
Each divider has a half-depth slot, and the two interlock at the crossing point while their ends sit in the walls. No glue is needed to keep the grid upright.
Can it be cut from 3 mm acrylic?
Yes on a CO2 laser; clear or frosted acrylic looks good on a buffet. Use the 3 mm file and acrylic cement rather than wood glue.
Is plywood safe on a table that gets wiped every day?
Seal all faces with oil or lacquer and wipe it with a damp cloth rather than soaking it. Unsealed plywood will swell where water stands.
How do I add my cafe logo?
Put the logo on the long front wall in your laser software and run it as an engrave or score step before the cut.
Similar files



