DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood box with its hinged lid tipped open on a kitchen counter, showing four sections with napkins, cork coasters, toothpicks and metal straws.Visualization
DW-105033 · UPDATED 11/19/2026

Hinged Box SVG, Napkin and Coaster Box with Flip Lid Laser Cut File, Wooden Table Storage Box DXF

A free hinged napkin box with a lid that flips open at the back, sized 300 × 180 × 100 mm (11.81 × 7.09 × 3.94 in) with four compartments inside. It assembles from 8 plywood pieces with tabs and slots, the lid pivots on pins cut into the side panels, and the download includes SVG and DXF files for 3, 4, 5 and 6 mm plywood.

Author
DXF World · 368 files
Formats
SVG, DXF
Outer size (W × D × H)
300 × 180 × 100 mm (11.81 × 7.09 × 3.94 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,100 × 296 mm
Cut length
7.71 m
Est. time, 10 W diode (3 mm)
25 min 41 s
Est. time, 40 W CO2 (3 mm)
10 min 42 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Select the file for your plywood thickness and cut a test slot and one pin hole to check the fit.
  2. 02Cut the 8 parts: front, back, two taller ends with pivot pins, base, two dividers and the lid.
  3. 03Assemble the walls on the base, slide the crossing dividers in, then set the lid on its pins and swing it a few times.
  4. 04Ease any tight pivot with sandpaper, finish the box with oil or lacquer, and fill the four sections.

How the lid works

The two end panels are a little taller than the walls and carry small pivot pins cut from the same plywood. The lid sits on those pins at the back, so it tips up and rests leaning back while you take something out, then drops shut. Nothing metal is involved and nothing has to be screwed. Inside, a long and a short divider cross to form four compartments, two at the back and two at the front. The photo shows white napkins and cork coasters in the back pair, with toothpicks and a set of metal straws in front.

Cutting and assembly tips

Eight pieces in total. On a 10 W diode the 3 mm file needs about 25 min 41 s; a 40 W CO2 does it in about 10 min 42 s and a 100 W CO2 in about 5 min 08 s. The 3 mm layout measures 1100 × 296 mm, so a smaller bed means splitting it, for example lid and base on the first sheet and the walls and dividers on the second. Assemble the box completely before seating the lid, and check that it swings freely; a light sanding of the pin holes fixes any stiffness. Do not glue the lid or the pins.

Gift and table ideas

A closed lid keeps napkins clean on a sideboard or an outdoor table where leaves and dust land. The flat lid takes an engraved monogram, a wedding date or a pattern you add yourself, which makes it a good housewarming or anniversary present filled with cloth napkins. Sealed with oil, it also works as a tea-light and match box or a cutlery box for a camper.

Questions about this file

Does the hinge need metal parts?

No. The lid turns on pins cut into the plywood end panels, so the box is all wood.

How wide does the flip lid swing open?

It swings up at the back far enough to reach all four sections, as the photo shows, and closes again under its own weight.

Is there a 6 mm version of this hinged napkin box?

Yes, there is a 6 mm version with matching slots and pins. It is heavier, so a diode laser will need several passes.

Should I glue the lid?

Never glue the lid or pins, or it will not open. Glue on the wall joints is optional.

Can I engrave the lid?

Yes, add your own design to the lid in your laser software and engrave it before cutting; the file has cut lines only.

Similar files