DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Birch plywood caddy with four sections on a beige stone counter, holding olive oil and vinegar bottles in the back and ketchup, mustard, ranch and chilli bottles in front.Visualization
DW-106003 · UPDATED 11/16/2026

Salad Dressing Caddy SVG, Four Section Condiment Organizer Laser Cut File, Fridge Sauce Bottle Tray DXF

A free laser cut file for an open salad dressing and sauce caddy with four sections in a two-by-two grid, a 100 mm back and a much lower front so the sides slope down. It is delivered as SVG and DXF in separate versions for 3, 4, 5 and 6 mm plywood, and the 8 pieces assemble with tabs and slots into a 300 × 160 × 100 mm (11.81 × 6.30 × 3.94 in) caddy.

Author
DXF World · 281 files
Formats
SVG, DXF
Outer size (W × D × H)
300 × 160 × 100 mm (11.81 × 6.30 × 3.94 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
940 × 272 mm
Cut length
5.54 m
Est. time, 10 W diode (3 mm)
18 min 28 s
Est. time, 40 W CO2 (3 mm)
7 min 42 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Find the SVG or DXF for your plywood thickness and cut a test slot to make sure the cross divider seats firmly.
  2. 02Cut the 8 pieces, including the tall back divider and the lower front-row divider.
  3. 03Join the back wall and tall divider to the base, slide the cross divider and front-row divider in, then fit both sloped sides and the low front.
  4. 04Round the top edges with fine sandpaper, apply a wipe-clean finish and stand two bottles in each pocket.

Eight bottles in four pockets

The caddy has two rows of two, and each pocket is wide enough for a pair of bottles. In the photo the back left holds two olive oils with gold caps, the back right a corked balsamic and a red wine vinegar, and the front pockets carry ketchup and mustard on one side and ranch with a chilli dressing on the other. The back row is divided by a full 100 mm divider, while the cross divider and the front-row divider are 79.6 mm high and the outer front wall only 60 mm. That stepped height keeps every cap within reach. It is the tallest of the open trays in this range, so it also works in a fridge door shelf or on a lazy Susan.

Making the caddy

For the 3 mm file, the job takes about 18 min 28 s on a 10 W diode, about 7 min 42 s on a 40 W CO2 and about 3 min 42 s on a 100 W CO2. A diode handles 3 mm in one or two passes; for 5 or 6 mm plywood go to a CO2 or plan multiple passes. The flat layout is 940 × 272 mm, so a smaller bed means two or three sheets. Fit the tall back divider to the back wall and base first, then the cross divider, the low front-row divider, the sides and the front. It holds without glue; glue the corners if it will be carried around full.

Selling and gifting

Dressing makers and small delis can fill it with four house dressings. For a barbecue set, sell it with a basting brush and two sauces.

Questions about this file

Will it fit in a fridge?

At 300 × 160 × 100 mm it fits most fridge shelves lying flat. Measure the door shelf first, because the 160 mm depth is more than many door bins.

Why is the back divider taller than the front one?

Tall oil bottles live in the back row and need support higher up. The lower front row keeps short dressing bottles visible.

Would 3 mm MDF do for a fridge caddy?

Yes, the 3 mm file works with MDF too. Seal it well, since MDF edges swell with moisture in a fridge or near a sink.

Should I glue the caddy?

A tabbed box holds fine dry on the counter. If you plan to carry it full to the table, a bead of wood glue in each corner is a good idea.

What finish suits a fridge or barbecue caddy?

A water-based polyurethane gives a hard, wipeable surface that copes with cold and condensation. Let it cure fully before the first use.

Similar files