DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Small light birch plywood napkin holder with three sections and a slanted front holding white napkins, cork coasters with toothpicks, and metal and glass straws on a sunny tableVisualization
DW-105091 · UPDATED 11/21/2026

Slant Front Napkin Holder SVG, Small Three Section Table Caddy Laser Cut File, Napkin and Coaster Holder DXF

A free compact napkin holder with three sections and a slanted front: the front wall is 48 mm high and the sides slope up to the 80 mm back, so napkins, coasters and straws are easy to pull out. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the holder measures 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in) and is built from 7 pieces that join with tabs and slots.

Author
DXF World · 530 files
Formats
SVG, DXF
Outer size (W × D × H)
240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in)
Parts
7
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
860 × 272 mm
Cut length
4.58 m
Est. time, 10 W diode (3 mm)
15 min 15 s
Est. time, 40 W CO2 (3 mm)
6 min 21 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Grab the file for your sheet thickness and test one divider in its slot on an offcut.
  2. 02Cut the 7 pieces in one run, or in two on a 400 mm bed.
  3. 03Seat the back and low front in the base, add the sloped sides, then push the two dividers in from the top.
  4. 04Ease the edges with sandpaper, apply oil or lacquer, and fill the three sections.

Small footprint, three jobs

At 240 × 180 mm this is the smallest open caddy in the napkin set, sized for a bistro table, a breakfast nook or the corner of a coffee table. Two dividers running front to back give three sections. In the photo the widest one holds a stack of white paper napkins leaning back against the rear wall, the middle one carries cork coasters with a small glass of toothpicks behind them, and the last is filled with metal and glass straws. The low 48 mm front lets you see what is left at a glance.

Cutting on a hobby laser

The 3 mm layout is 860 × 272 mm, so on a 400 mm bed it splits neatly into two runs: base and long walls, then the sides and dividers. The estimated time for the 3 mm file is about 15 min 15 s on a 10 W diode, about 6 min 21 s on a 40 W CO2 and about 3 min 03 s on a 100 W CO2, which makes it a quick piece to batch for markets. A diode laser cuts 3 mm in one or two passes; allow extra passes or a CO2 machine for 5 and 6 mm plywood.

Finishing and selling

The seven parts lock together on their tabs; add glue only if you want it permanent. Round the top edges with fine sandpaper, then finish with a food-safe oil or a clear water-based lacquer. Because it cuts fast and uses little material, it is a good product for a stall: offer it plain, stained, or with a short phrase engraved on the front, and bundle it with a pack of printed napkins as a hostess gift.

Questions about this file

Is it big enough for regular napkins?

Yes. Folded paper napkins stand on edge in the wide section and lean back against the 80 mm rear wall, as the photo shows.

How long does a batch take?

On a 40 W CO2 one holder takes about 6 min 21 s for the 3 mm file, so a batch of ten fits into roughly an hour of cutting.

Can I cut it in MDF?

Yes. 3 mm MDF cuts cleanly and is easy to paint in a cafe colour; seal the edges so it does not swell.

Can I make it longer with more sections?

Stretching the drawing distorts the tabs, so redraw the slots at your sheet thickness if you change the size.

Does it need glue?

No. The tabs and slots hold it square for daily use. A drop of wood glue in each base joint makes it permanent.

Similar files