DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Black metal panel of two horse heads nuzzling above a leaf border, standing on a wooden sideboard with small feet bracketsVisualization
DW-300008 · UPDATED 11/20/2026

Two Horses SVG, Facing Horse Heads Wall Art Laser Cut File, Leafy Base Equestrian Decor DXF

A single-panel cut file of two horse heads facing each other, one with a long flowing mane, standing on a band of cut-out leaves. It is a free download with one SVG and one DXF file, drawn at 317.5 × 231.1 mm (12.5 × 9.1 in), cut lines only, and it can be scaled for a shelf piece or a large wall panel.

Author
DXF World · 415 files
Formats
SVG, DXF
Size
318 × 231 mm (12.50 × 9.10 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
9.07 m
Est. time, 10 W diode (3 mm)
30 min 14 s
Est. time, 40 W CO2 (3 mm)
12 min 36 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Open the SVG or DXF and set the width you want; keep the long mane strands at least 2 mm wide.
  2. 02Cut the small eye and nostril holes first, then the mane slots, and the outer outline last so the panel stays put.
  3. 03Lift the panel out carefully and clear any leaf or mane offcuts that stayed in place.
  4. 04Sand or wipe the edges, paint or oil the face, and fit brackets or a hanger.

What the design shows

Two horses meet nose to nose. The left one faces you with a forelock and a short braided mane; the right one turns in from the side, with a long mane falling in separate strands down its neck. Facial lines, eyes and nostrils are open slots, so light or the wall colour shows through. A strip of leaf shapes runs along the bottom and ties the whole outline into one solid piece, which keeps it stiff enough to stand on a shelf as well as hang.

Scaling and material

At the drawn size of 317.5 × 231.1 mm the mane strands and the thin lines around the eyes are already fine. Keep it at this size or larger in 3 mm plywood or MDF; if you shrink it a lot, those bridges get weak and can snap when you lift the piece out. In 3 mm acrylic the detail holds well and black or mirror gold looks sharp. For a big outdoor or barn sign, scale it up to 600–900 mm and cut it from steel on a plasma table or from 6 mm plywood on a CNC router with a small end mill.

Where to hang it and gift ideas

Over a tack room door, in a stable office, above a bed in a horse lover's room or on a mantel. To make it stand, add two small L-brackets under the leaf border, as in the photo, or glue it into a slotted wooden base. Painted matte black on a light wall it reads clearly from across the room. As a gift it suits riding school awards, a thank-you for a farrier or trainer, or a pair of these for a couple who keep horses together.

Questions about this file

Is this one piece or several layers?

It is one flat panel. Both horses and the leaf band share a single outline, so there is nothing to glue together.

How small can I make the two horses?

About 250 mm wide is a sensible minimum in plywood. Below that the strands of the mane become thinner than the wood is thick and break easily.

Can it be cut in metal?

Yes. The closed outline works on a plasma or fiber laser; scale it up first so the thin eye lines survive the larger kerf.

How do I make it stand on a shelf?

Screw two small angle brackets behind the leaf border, or cut a base board with a slot as wide as your material.

What finish suits a stable or barn?

Exterior paint or spar varnish on plywood, or powder coat on steel. Seal the cut edges too, since that is where moisture gets in.

Similar files