VisualizationDolphin Hook Rack SVG, Beach House Towel Hanger Laser Cut File, Nautical Key Holder DXF, Sea Wall Hooks Plasma Cut
A one-piece wall rack with three dolphins leaping over a bar that ends in two pointed screw tabs, with four straight prongs hanging below for towels, keys or leashes. The free download has one SVG and one DXF with cut lines only, sized 421.6 × 345.4 mm (16.6 × 13.6 in), for a laser or CNC router in plywood or acrylic, or a plasma table in steel.
- Formats
- SVG, DXF
- Size
- 422 × 345 mm (16.60 × 13.60 in)
- Material
- Plywood, MDF, acrylic or metal (scale to your piece)
- Cut length
- 3.45 m
- Est. time, 10 W diode (3 mm)
- 11 min 29 s
- Est. time, 40 W CO2 (3 mm)
- 4 min 47 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Open the file at 421.6 × 345.4 mm, or scale it to your wall, and look at the thin parts between the dolphin tails before cutting.
- 02Cut the eye holes, inner windows and screw holes first and the outline last, so the panel stays put on the bed.
- 03Bend the four prongs forward for a metal rack, or glue a dowel peg near the end of each prong for wood or acrylic.
- 04Paint or seal the rack, then fix it to the wall through the two tab holes with screws and wall plugs.
What the file contains
The whole rack is a single panel. Three dolphins arc over each other at the top: a large one jumping from left to right and two smaller ones meeting nose to nose on the right. Open windows between their bodies keep the piece light, and each dolphin has a small eye hole. The bar underneath ends in two leaf-shaped tabs with one screw hole each, and four prongs of equal length drop from it, spaced roughly 9 cm apart. The photo shows it in matte black.
Turning the prongs into hooks
In sheet steel or aluminium, clamp each prong near its root and bend the lower half forward and up to make a real hook; a plasma-cut rack in 2–3 mm steel takes coats and bags. In plywood, MDF or acrylic the prongs cannot bend, so glue a short dowel or a round knob near the end of each one, or twist a small brass cup hook into the face. Keep the full size when the rack has to carry weight. Scaling it down a lot thins the bridges between the fins and tails, so look at those parts again after resizing.
Where it works
- Beach house or lake cabin entry for keys, sunglasses and dog leashes.
- Bathroom wall for hand towels and robes, sealed well or cut from acrylic.
- Pool shed or boat cabin for snorkels, caps and swim gear.
- A gift for a diver or sailor, painted ocean blue or left plain black.
Questions about this file
Can the prongs hold anything if I cut the rack from wood?
Not on their own, because flat prongs lie against the wall. Add a short dowel, a knob or a screw-in cup hook to each prong.
What steel thickness suits a plasma-cut version?
Sheet of 2–3 mm is a common choice for a hook rack of this size. Thinner sheet is easier to bend but sags under heavy coats.
Can I make it smaller for keys only?
Yes, a rack around 25–30 cm wide still holds keys well. Check that the bridges between fins stay wider than your material is thick.
Is it suitable for a damp bathroom?
Seal plywood on all faces and edges, or cut it from acrylic or powder-coated steel, which do not swell.
Where can I add a name or a beach town?
Engrave it on the solid bar above the prongs, between the two screw tabs, where there is a clean strip.
Similar files



