DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
White painted panel with an Islamic star lattice of large twelve-point stars leaning against a beige wall, casting patterned shadows on the floorVisualization
DW-300049 · UPDATED 11/21/2026

Islamic Geometric Screen DXF, Arabic Star Lattice Room Divider Cut File, Moorish Wall Panel SVG, CNC Jali Screen

A full-size decorative screen panel with a classic Islamic geometric pattern: six large twelve-point star rosettes in two rows, linked by interlaced strapwork with small stars and kite shapes, inside a narrow border. The free download is one SVG and one DXF file, 2000 × 1200 mm (78.74 × 47.24 in), cut lines only, sized for one standard CNC router sheet or a large-format laser.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
2,000 × 1,200 mm (78.74 × 47.24 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
102.09 m
Est. time, 10 W diode (3 mm)
340 min 19 s
Est. time, 40 W CO2 (3 mm)
141 min 48 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Load the panel and check that the 2000 × 1200 mm size fits your router sheet or laser bed, or split it in two.
  2. 02Run a test of one small star with your chosen bit or laser power to confirm the points come out sharp.
  3. 03Cut the inner openings first with holding tabs, then the outer border, and remove the tabs with a chisel or file.
  4. 04Sand the strapwork, prime and paint (MDF) or seal (plywood), and mount it in a frame or on standoffs.

The pattern

The panel is landscape: three large twelve-point stars across and two rows down, each one the hub of a wheel of strapwork bands. Between the wheels the bands cross to form small stars, diamonds and long kite-shaped openings, and the pattern runs off all four edges into a plain border, so two panels placed side by side continue the design. The photo shows it in white painted MDF leaning against a wall, throwing a star-shaped shadow across the floor.

Cutting a 2 m panel

  • CNC router: the size fits a 2440 × 1220 mm sheet of MDF or plywood with a margin for clamping. Use a 3 mm or 1/8 in end mill for the small stars; a 6 mm bit will round off their points.
  • Laser: you need a 1300 × 2500 mm bed, or split the panel into two 1000 × 1200 halves along a strapwork band and join them on a frame.
  • Plasma or fiber laser: 1.5–2 mm steel or aluminum makes a garden screen or a gate infill.

The file has a few hundred small cut-outs, so run a slow tab or hold-down strategy and keep small offcuts from tipping into the bit. The outer rectangle is drawn twice on top of itself; delete one copy so the edge is not cut twice.

Where to use it

As a free-standing room divider in a frame, a wall panel with LED strip behind it, a radiator cover front, a headboard, or a ceiling panel over a light. Scaled down to 600 × 360 mm, it makes a decorative tray insert or a lantern side.

Questions about this file

What thickness is best for a free-standing screen?

12–18 mm MDF or plywood on a CNC router; at 2 m tall, thinner sheet flexes unless it sits in a frame.

Can I make the panel smaller?

Yes. It scales cleanly, but below about 50% the strapwork bands get thin, so switch to a thinner material at the same time.

Does the pattern continue across several panels?

The stars run off the edges inside the border, so panels placed next to each other read as one long screen.

Is MDF safe for a bathroom partition?

Use moisture-resistant MDF and seal every cut face with primer before painting, or switch to PVC foam board or aluminum.

How do I light it from behind?

Fix the panel 30–50 mm off the wall on spacers and run an LED strip around the back edge for a soft star pattern on the wall.

Similar files