DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
White Voronoi cell panel with a solid border leaning against a cream wall, irregular cells fanning out from a small round centerVisualization
DW-300016 · UPDATED 11/20/2026

Voronoi Panel SVG, Geometric Wall Art Laser Cut File, Organic Cell Pattern DXF, Modern Screen Insert CNC File

A rectangular geometric panel cut through with 232 openings: irregular Voronoi cells that turn into narrow wedges around a small round hub near the middle, held together by a solid outer border. The free download has one SVG and one DXF with cut lines only at 406.4 × 307.3 mm (16 × 12.1 in), for plywood, MDF or acrylic, and it scales to a cabinet insert or a large wall panel.

Author
DXF World · 415 files
Formats
SVG, DXF
Size
406 × 307 mm (16.00 × 12.10 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
17.26 m
Est. time, 10 W diode (3 mm)
57 min 32 s
Est. time, 40 W CO2 (3 mm)
23 min 58 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Pick your size; at 406.4 × 307.3 mm the webs are about 5 mm and they get thinner if you scale down.
  2. 02Cut the 232 openings first and the border last, with the sheet pinned flat.
  3. 03Push out the cell scraps and sand both faces lightly to remove the edge residue.
  4. 04Paint or stain, then mount it on spacers, in a frame or on a cabinet door.

How the pattern is built

The cells are not a uniform grid. Close to the hub they are thin wedges arranged like the spokes of a web, and further out they open into larger rounded polygons that run up to the border. The webs between cells keep a fairly even width, about 5 mm at the file size, so the panel reads like cracked earth or a dragonfly wing rather than a mandala. The photo shows it painted white and leaning against the wall as a framed screen.

Cutting tips

With this many openings the cut path is long and the order matters: run all cells first and the outer border last, and pin or weigh the sheet so it cannot move once the panel is loose. Thin plywood can warp a little after so many cuts, while 4–6 mm plywood or 3 mm MDF stays flatter. In acrylic, use air assist so neighbouring cells do not melt into each other at the narrow webs. When you scale the design down the webs shrink in step, so keep them at least 2 mm wide.

Ways to use it

Hang it as it is, or mount it a few centimetres off a coloured board so the cells cast shadows. Put an LED strip and a white diffuser behind it for a light box, fit it into a sliding cabinet door, or use it as a radiator cover front. A set of three in different colours looks good side by side. For a full wall version, enlarge it and cut MDF on a CNC router.

Questions about this file

Why did my panel warp after cutting?

Many cuts release tension in the sheet. Use flat, good-quality plywood or MDF and weigh it down on the bed.

Can I turn it into a light box?

Yes. Put a white acrylic or paper diffuser and an LED strip behind it in a shallow box frame.

How small can I make it?

Keep the webs at least about 2 mm wide, which is roughly 40 percent of the file size, around 165 mm across.

Can a CNC router cut it?

Yes, at larger sizes. Enlarge it until the smallest wedges near the hub are wider than your bit, then cut MDF or plywood.

Does it work in acrylic for a window?

Frosted or coloured acrylic looks good against daylight. Leave the masking film on until after cutting to keep the faces clean.

Similar files