VisualizationSquare Side Table SVG, Slot Together Coffee Table DXF, Plywood End Table CNC File, Inset Top Table Plans
A small square side table cut from flat sheet stock and joined with tabs and slots: two leg frames with tapered legs, two side rails, a slotted top frame, a plain border frame and a square top panel, 7 pieces in all. You get one SVG and one DXF file with cut lines only, laid out on 1366.4 × 877.7 mm (53.8 × 34.56 in), free to download. The leg frames are about 400 mm wide and 300 mm tall, and the slots are drawn for one material thickness that you check in your software before cutting.
- Formats
- SVG, DXF
- Size
- 1,366 × 878 mm (53.80 × 34.56 in)
- Material
- Plywood, MDF, acrylic or metal (scale to your piece)
- Cut length
- 13.18 m
- Est. time, 10 W diode (3 mm)
- 43 min 56 s
- Est. time, 40 W CO2 (3 mm)
- 18 min 18 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Measure a slot in the top frame, match your sheet to it, and test-cut one rail before the full layout.
- 02Cut all seven pieces; on a small machine, split the layout into two or three jobs.
- 03Push both leg frames and both rails up into the slotted top frame and check that the legs stand square.
- 04Lay the square panel into the top opening, glue the border frame over it, then sand and paint.
What the seven pieces do
The two U-shaped leg frames form the ends of the table. Each has two slightly tapered legs and a row of tabs along its top edge. The two straight rails close the other two sides and carry the same kind of tabs. All four parts plug up into the slotted top frame, which has notches along every edge. The square panel fills the opening in the top, and the plain border frame sits over it like a picture frame, so the panel edge stays hidden. The photo shows the table painted white with a tinted glass panel in the top.
Slot width and material
The tabs and slots are drawn for one sheet thickness, and the file does not state it. Open it in your software, measure the width of a slot in the top frame, and buy plywood or MDF to match. If your sheet is thinner or thicker, scale the whole file until the slot equals your material, then cut one rail and a corner of the top frame as a test. The layout is 1366.4 mm long, so most people will cut it on a CNC router or a large CO2 laser; on a smaller bed, move the pieces onto two or three sheets.
Finishing the top
Sand the tabs lightly before assembly, because paint makes a tight joint tighter. Glue the joints if the table will carry weight every day. A clear acrylic or glass panel lets you show photos, pressed flowers or a map underneath; a painted MDF panel is the simplest choice. Seal the top with a hard varnish if drinks will stand on it.
Questions about this file
How big is the finished table?
The leg frames are about 400 mm wide and 300 mm tall, and the top frame is about 400 mm square. Scale the file for a larger table, but keep the slots matched to your sheet.
What thickness of plywood does it need?
The file does not say. Measure the slot width in your software and use material of that thickness, or scale the file until the slot matches what you have.
Can I put glass in the top?
Yes. Have glass or acrylic cut to the size of the square panel and use it in place of the wooden one, or lay it on top of the wood.
Can a small diode laser cut this table?
Only in several jobs and with patience, since the layout is over 1.3 m long and furniture stock is thick. A CNC router or a large CO2 laser suits it better.
Does it need glue?
The tabs hold it for a dry fit. For a table that gets leaned on, glue every joint and let it cure before use.
Similar files



