DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Square MDF lamp box with a swirl and sun ray fretwork window on each side and a flat lid, standing on a wooden table in a living roomVisualization
DW-300093 · UPDATED 11/21/2026

Hamsa Night Light SVG, Square Fretwork Lamp Laser Cut File, Evil Eye Lantern DXF, Sun Ray Table Lamp Box

A small square table lamp whose four walls each show a hamsa hand filled with spirals and an eye at its centre, framed by sun rays, with a solid lower band and little feet. Everything sits in a free SVG plus DXF pair with cut lines only, laid out on a 500.9 × 452.7 mm (19.72 × 17.82 in) layout, with 3 mm slots, two square plates and four plain inner liners.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
501 × 453 mm (19.72 × 17.82 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
16.64 m
Est. time, 10 W diode (3 mm)
55 min 29 s
Est. time, 40 W CO2 (3 mm)
23 min 07 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Cut one wall and the shelf plate from 3 mm sheet and test the slot fit.
  2. 02Cut all four walls, both square plates and the four liners from diffuser material.
  3. 03Glue a liner behind each window, join the walls, slide in the shelf plate and fit the LED light.
  4. 04Run the cable through the side hole, put the lid on and finish the outside with paint or oil.

What you cut

Four wall panels about 106 mm wide and 169 mm tall make the box. Each has the hamsa window at the top, a long 3 mm slot below it and a notch at the bottom that leaves two feet. One wall has a small round hole for the cable. Two square plates with notched corners close the top and form a shelf: the one with a centre hole holds a lamp socket or an LED puck. On the right of the layout are four plain rectangles the size of the windows; cut them from tracing paper, vellum or 2 mm frosted acrylic and glue them behind the fretwork to soften the light. The photo shows the finished box in MDF with dark edges.

Cutting and assembly

The slots are 3 mm wide, so stick to 3 mm plywood, MDF or acrylic. The spirals have thin walls; on a diode laser run them at a speed that cuts cleanly in one pass to avoid burning through the bridges. Join the four walls at the corners, slide the shelf plate into the slots, feed the cable through the side hole and put the lid on last so you can still change the bulb.

Finishing and gift ideas

Use only a cool LED bulb or an LED puck light. Painted white, the box suits a nursery or a yoga room; in natural birch it fits a boho bedroom. A hamsa lamp makes a thoughtful housewarming or new-baby gift, and a set of two works on bedside tables.

Questions about this file

What light should I put inside?

A small LED bulb on a cord set or a battery LED puck. Avoid hot incandescent bulbs in a wooden box.

What are the four plain rectangles for?

They are liners for the windows. Cut them from paper, vellum or frosted acrylic to diffuse the light.

Can I make a taller floor lamp from it?

Scaling changes the 3 mm slots too. Scale by the same ratio as your new sheet thickness, or redraw the slots.

Is the motif religious?

The hamsa is a traditional protective hand symbol shared by several cultures. Many buyers choose it simply as boho decor.

Can I cut it in acrylic?

Yes. White or frosted 3 mm acrylic glows on its own, so you can skip the liners.

Similar files