DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Three hexagonal wooden lanterns with diamond lattice walls, small cupolas and ring handles, decorated with ribbons and snowflakes, glowing on a tableVisualization
DW-300083 · UPDATED 11/21/2026

Hexagonal Lantern SVG, Lattice Candle Lantern Laser Cut File, Wooden Tea Light Lantern DXF, Christmas Table Lantern

A six-sided wooden lantern with diamond lattice walls, a hexagonal roof, a small lattice cupola on top and a ring handle, built with tabs and 3 mm slots. The whole lantern is a free SVG and DXF pair holding cut lines only, on a 309.6 × 406.8 mm (12.19 × 16.02 in) layout; one hexagon is meant as a thin metal heat plate under the roof.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
310 × 407 mm (12.19 × 16.02 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
14.26 m
Est. time, 10 W diode (3 mm)
47 min 33 s
Est. time, 40 W CO2 (3 mm)
19 min 49 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Cut one wall panel and the roof hexagon from your 3 mm sheet and check the tab fit.
  2. 02Remove the text label from the metal plate shape and cut all the wooden parts.
  3. 03Plug the six walls into the floor, cap them with the roof and collar, then build the cupola from its six small panels.
  4. 04Lock on the ring handle, add the finish and ribbons, and place an LED tea light inside.

Parts of the lantern

Six tall wall panels carry a criss-cross diamond lattice with tabs along both short edges. Two large slotted hexagons form the floor and the roof, a hexagonal ring with a round opening sits as a collar, and a smaller slotted hexagon plus six little lattice panels build the cupola. A round ring handle with a locking tongue tops it off. The last hexagon with tabs is marked in the file as a metal plate: cut it from thin sheet metal, or leave it out if you only use LED candles. The photo shows three lanterns with a frosted brown finish, snowflake appliqués and ribbons.

Cutting notes

The slots measure 3 mm, so use 3 mm plywood or MDF and test one wall tab in a roof slot before cutting the full set. Delete the small text label on the metal plate first, or your laser will cut the letters. The lattice has many sharp inside corners; cut it with air assist and a slightly slower speed so the thin crossbars do not scorch through. Everything fits on a sheet of about 31 × 41 cm.

Light, finish and selling

Use LED tea lights or a battery fairy light string inside; a real flame in a wooden lantern needs the metal plate and constant supervision. A dry-brushed white over dark stain gives the snowy look in the photo. Sell them in sets of three for Christmas markets, wedding aisles or café tables, with ribbon colours to match the season.

Questions about this file

Can I use a real tea light?

Only with the metal plate under the roof and never unattended. LED tea lights are the safe choice for a wooden lantern.

What thickness is it drawn for?

The slots are 3 mm. Thicker plywood will not fit without redrawing the slots.

How do I get the candle in?

Set the candle on the floor plate before the roof goes on, or leave the roof unglued so it lifts off.

Can I make a bigger floor lantern?

Scale it up only together with thicker material at the same ratio, for example 200 percent for 6 mm sheet, and test a joint.

How do I get the frosted look?

Stain it dark brown, then dry-brush white acrylic paint lightly over the lattice and edges.

Similar files