DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Birch plywood slot-together open-wheel race car with drum wheels and a tall rear wing on a wooden desk in a bright kids roomVisualization
DW-300075 · UPDATED 11/21/2026

Race Car 3D Puzzle SVG, Open Wheel Racer Model DXF, Slot Together Wooden Car Laser Cut File, Desk Model Kit

A slot-together 3D model of an open-wheel single-seater race car with a long nose, front and rear wings, side pods, a raised cockpit and four wide drum wheels. The free SVG and DXF hold cut lines only for dozens of flat parts on a 352.8 × 433.5 mm (13.89 × 17.07 in) layout; the parts lock together with slots, so the material must match the slot width.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
353 × 434 mm (13.89 × 17.07 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
12.91 m
Est. time, 10 W diode (3 mm)
43 min 01 s
Est. time, 40 W CO2 (3 mm)
17 min 56 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Measure the slot width in the file, choose matching plywood or MDF, and test-fit one wheel disc with one spacer.
  2. 02Cut the whole layout, keeping the small spacers and wing end plates together in a tray.
  3. 03Assemble the four wheel drums, then slot the cockpit, engine cover and roll hoop into the floor.
  4. 04Fit the front and rear wings, add the wheels, glue the loose joints and finish with paint or clear lacquer.

What you build

The chassis starts from a long flat floor with the nose and the side pods, and the upright parts slot into it: the cockpit sides, the engine cover with its tall fin, the driver's headrest and the roll hoop. A wide rear wing on two end plates sits at the back and a low front wing with its own end plates sits under the nose. Each wheel is a drum: several round discs with notches at four points, held apart by short ribbed spacers, which gives the chunky slick-tyre look in the photo.

Slot width and material

The slots are drawn for one material thickness, and the file does not say which. Open it in your software and measure the width of a few slots, then use plywood or MDF of that thickness. If you want a different material, scale the whole file until the slots match it. Cut one wheel disc and one spacer first and push them together: a firm fit without forcing is what you want. Kerf matters a lot here, because there are many joints.

Assembly and display

Build the wheels first, as they are the most repetitive part, then the floor and the cockpit, the wings last. Most joints hold by friction; a drop of wood glue on the wing end plates and the wheel hubs keeps the model together on a shelf. Stain the body and leave the wings natural, or paint it in your favourite racing colours. As a gift for a motorsport fan or a teen who likes building, it makes a long evening project.

Questions about this file

What thickness is this race car for?

The thickness is not written in the file. Measure the slot width in your software and use that thickness, or scale the file to suit the plywood you have.

Should I paint the parts before or after assembly?

Paint flat parts before assembly only away from the slots, since paint adds thickness and tightens joints. Otherwise build first and spray the finished car.

How long does assembly take?

There are many small parts, so plan an evening. Sorting the parts by type before you start saves time.

Can I cut it on a small diode laser bed?

Yes, but the 352.8 × 433.5 mm layout may need splitting into two jobs. Move the parts around in your software and keep the slots unscaled.

Is it suitable for children to build?

Older kids enjoy it with an adult nearby. Sand the small parts well, because the spacers and wing plates have tight corners.

Similar files