DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood plaque with a six-petal fretwork flower, diamond motifs and curled leaves in a notched raised frame, standing on a wooden tableVisualization
DW-300055 · UPDATED 11/21/2026

Folk Flower Plaque SVG, Layered Tile Ornament Laser Cut File, Six Petal Fretwork Sign DXF, Wooden Wall Tile

A decorative folk-style tile plaque with a six-petal flower in the middle, four diamond motifs and curled leaves, framed by a notched outline with small round ears on each side. The free download is one SVG and one DXF file, 210.8 × 147.3 mm (8.30 × 5.80 in), cut lines only; it cuts into a thin outer frame ring and a fretwork center panel that stack into a two-level plaque.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
211 × 147 mm (8.30 × 5.80 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
5.10 m
Est. time, 10 W diode (3 mm)
17 min 00 s
Est. time, 40 W CO2 (3 mm)
7 min 05 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Cut a 20 mm test piece with one petal slit to check that your power cuts the fine vein lines cleanly.
  2. 02Cut the plaque file, then cut the outer outline alone from a second sheet as a solid backer.
  3. 03Glue the fretwork panel onto the backer and set the narrow frame ring on top, pressing it flat while it dries.
  4. 04Sand the edges lightly, paint the backer in a contrast color if you like, and seal with clear lacquer or oil.

What the file cuts

The outline is a wide rectangle with arched sides, rounded corners and small round notches, the kind of shape you see on painted folk tiles. Just inside it runs a narrow frame ring. The center panel carries the ornament: six rounded petals around an oval eye, each petal with a few fine vein slits, a diamond motif at the top, bottom, left and right, and pairs of curled leaves between them. Cut it and you get two parts, the thin frame and the pierced panel. The photo shows them stacked in birch plywood, with the frame raised above the panel and a plain sheet behind so the petals read as shallow pockets.

Making it two or three levels

For the backer, cut the outer outline once more from solid sheet and delete everything inside it. Glue the fretwork panel onto the backer, then the frame on top. A contrast works well: white MDF behind natural plywood, or a dark stained back under a light top layer. At 210 mm wide the petal vein slits are fine, so a 3 mm sheet is the safe choice; if you scale the plaque up to 400 mm or more, 4–6 mm plywood or MDF is fine and the slits get easier to cut. Scaling down below about 150 mm makes the bridges between the leaves weak.

Where it fits

As a small easel plaque on a shelf, a trivet-style tile on a kitchen wall, a lid inlay for a wooden box, or a set of four on a cabinet door. Painted in blue and white it looks like a ceramic tile; left raw and oiled it fits a rustic kitchen. Sold as a pair of mirror-image plaques, it makes an easy housewarming gift.

Questions about this file

How many parts does the file make?

Two: a narrow outer frame ring and the center panel with the flower. The solid backer is cut separately from the outer outline.

Can I use it as a single flat panel?

Yes. Glue the frame ring straight back around the panel on a backer, or skip the frame and cut only the outer shape with the ornament inside.

What material suits this small size?

3 mm birch plywood or MDF. Acrylic also works and gives crisp petal edges, especially as a colored top layer over a white back.

Could it be a box lid or furniture appliqué?

Yes. Scale it to the lid or door panel, keep at least 2 mm of material between cut-outs, and glue it on as an overlay.

How do I hang it?

Glue a sawtooth hanger or a small keyhole plate on the back of the backer, or stand it on a plate stand as in the photo.

Similar files