DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Wooden number puzzle board with digits, plus, equals, brackets and slash pieces set into a frame, standing on a desk in a kids' roomVisualization
DW-300044 · UPDATED 11/21/2026

Cyrillic Alphabet Puzzle SVG, Russian Letter Board Laser Cut File, Wooden Number Puzzle DXF, Kids Learning Board

Two layered wooden learning puzzles in one file: a large board with the 33 letters of the Russian Cyrillic alphabet and a smaller board with the digits 0 to 10 and plus, minus, equals, bracket and slash signs. Both boards come free in a single SVG and a single DXF, cut lines only, laid out on 945.7 × 480.5 mm (37.23 × 18.92 in); each board is a plain back, a frame with letter-shaped holes and the loose pieces.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
946 × 481 mm (37.23 × 18.92 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
22.58 m
Est. time, 10 W diode (3 mm)
75 min 15 s
Est. time, 40 W CO2 (3 mm)
31 min 21 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose plywood for the back and frame layers and cut a corner of the frame as a test.
  2. 02Cut the two back plates, the two frames and the separate sets of letters, digits and signs.
  3. 03Glue each frame onto its back plate and clamp it flat until dry.
  4. 04Sand the letters and digits, finish them with toy-safe paint or oil, and set them in.

Two boards in one file

The alphabet board has six rows of chunky rounded capitals, from the first letter of the alphabet to the last, in the order children learn them. The number board holds 1 to 9, a 10, a 0 and the signs needed for simple sums: plus, minus, equals, two brackets and a slash. Both are built the same way: a solid back plate, a frame plate with the cut-out shapes, and the shapes themselves, which drop back into their holes. The photo shows the number board finished in oak-look plywood with the pieces in place.

Cutting and assembly

The loose letters and digits are drawn as their own set next to each frame, so they come out with a clean edge all round; the bits that drop out of the frame holes are offcuts or a spare set. Glue the frame onto the back plate with a thin bead of wood glue and clamp it flat. Rounded letters like these survive small sizes well, but the counters inside some letters get narrow if you shrink the board a lot. Birch plywood of 3 to 6 mm suits both layers; a 10 W diode handles 3 to 4 mm in one or two passes.

Finishing and gift ideas

Sand the letter edges and use a toy-safe oil or water-based lacquer. Colour every letter differently with food-grade paint for younger kids. Families teaching Russian, Ukrainian or Bulgarian at home look for these boards, and a name engraved on the frame turns one into a personal birthday gift.

Questions about this file

Which alphabet is it?

The Russian Cyrillic alphabet with all 33 letters. Ukrainian and Bulgarian use most of the same shapes but have a few different letters.

Are the loose letters part of the frame cut?

No, they are a separate set drawn beside each frame. Check the fit of one letter in its hole and adjust the kerf if it is too tight.

Can I make only the number board?

Yes. Select the small back, frame and number pieces and delete the alphabet before cutting.

Is it safe for toddlers?

Sand every edge and use a toy-safe finish. Small signs like the minus and the slash are a choking risk for children under three.

Can I scale it down for a smaller laser?

Yes, it has no slots, so any size works. Below about half size the holes inside some letters get very thin.

Similar files