DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Oak frame-and-panel cabinet door with grooved boards, a raised clipped-corner frame and a spindle-shaped opening, hung on a beige wallVisualization
DW-300057 · UPDATED 11/21/2026

CNC Cabinet Door Design DXF, Kitchen Door Front Pattern Cut File, Raised Frame Door Overlay SVG, Router Groove Door

A line drawing for a 400 × 600 mm (15.75 × 23.62 in) cabinet door front: an outer border, a center panel divided into horizontal boards by straight groove lines, a raised inner frame with clipped corners and a decorative spindle-shaped opening in the middle. The free download is one SVG and one DXF file in mm, made for a CNC router (grooves and pockets) or for cutting the frame and spindle as appliqué parts on a laser.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
400 × 600 mm (15.75 × 23.62 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
6.25 m
Est. time, 10 W diode (3 mm)
20 min 49 s
Est. time, 40 W CO2 (3 mm)
8 min 41 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Measure your cabinet opening and stretch the straight sections of the drawing to fit, leaving the spindle at its size.
  2. 02Assign toolpaths: pocket the center panel, V-groove the board lines, profile the raised frame, cut the spindle through.
  3. 03Run the job on a scrap first to check depths, then cut the door blank.
  4. 04Sand the grooves and edges, prime or stain, and hang the door with your usual cabinet hinges.

What the drawing shows

The outer rectangle is the door blank. About 70 mm in from the edge, a second rectangle marks the recessed center panel, which ten short straight lines split into horizontal boards. In the middle sits a narrower frame with angled, clipped corners, and inside that a tall slot holding a symmetrical spindle shape, like a turned baluster with pointed ends. The photo shows the look in oak: a flat frame-and-panel door with the clipped-corner frame raised and the spindle opening cut right through.

Two ways to make it

CNC router. Treat the lines as toolpaths. Pocket the center panel 3–5 mm deep, run a V-bit along the board lines, profile the clipped-corner frame so it stands proud, and cut the spindle through. 18 mm MDF or solid wood suits a kitchen or wardrobe door.

Laser or scroll saw. Cut the clipped-corner frame and the spindle opening from 3–6 mm plywood as a separate overlay, and glue it onto a plain door. Score the board lines with a light engrave pass on the door face, or skip them.

The file is a single door; mirror it for a pair of doors and stretch only the straight sections if your cabinet is taller, so the clipped corners and spindle keep their shape.

Finishing

Paint-grade MDF takes a satin enamel well; prime the routed grooves twice. For wood, stain before fitting hinges and seal the cut-through spindle edges so they match the face.

Questions about this file

Is this a through-cut panel or a carving?

Mostly a carving pattern. Only the spindle shape is meant to go right through; the other lines are pockets, grooves and the raised frame.

Can I use it on a laser?

Yes, as an overlay: cut the clipped-corner frame and the spindle opening from thin plywood and glue them onto a flat door.

Will it fit my kitchen cabinets?

It is drawn at 400 × 600 mm. Stretch the straight lines to your door size rather than scaling, so the corners and spindle stay in proportion.

What should go behind the spindle opening?

Leave it open for airflow, or glue glass, mesh or fabric behind it for a display cabinet.

Which bit works for the board lines?

A 60 or 90 degree V-bit gives a clean plank look; a small ball-nose bit gives softer grooves.

Similar files