Laser Cut Makeup Organizer Files: 12 Free SVG and DXF Boxes
A laser cut makeup organizer is a tab-and-slot plywood box with dividers sized for brushes, lipsticks and palettes. The 12 files below range from a 6-part, 260 × 160 mm caddy to a 13-part, 270 × 270 mm nine-cell grid; each comes in SVG and DXF for 3, 4, 5 and 6 mm plywood and cuts in about 13–29 minutes on a 10 W diode (3 mm file).
A makeup organizer often goes from the laser bed straight to a dressing table, still smelling faintly of smoke. By the evening every lipstick stands in a row, and the palettes that used to slide around a drawer finally have a home. That is the charm of a laser cut makeup organizer: forty minutes of work, and a messy surface turns into something that looks bought in a design shop.
Below are 12 makeup organizer files from the DXF World library, picked so that every type of vanity gets a match: small caddies, long shelf organizers, palette stands and big grids. Every file is a tab-and-slot box with sloped sides, and every download has SVG and DXF versions for 3, 4, 5 and 6 mm plywood. All of them live in the makeup organizers category.
The 12 makeup organizers at a glance
| File | Outer size, mm | Cells | Parts | 10 W diode, 3 mm |
|---|---|---|---|---|
| Two-section caddy | 260 × 160 × 100 | 2 | 6 | about 13 min |
| Slanted, 3 sections | 280 × 160 × 100 | 3 | 7 | about 16 min |
| Lipstick ledge | 280 × 200 × 90 | 3 | 7 | about 17 min |
| Tiered, 3 rows | 280 × 220 × 90 | 3 | 7 | about 19 min |
| Square, 4 cells | 220 × 220 × 90 | 4 | 8 | about 17 min |
| Palette tray, 3 side cells | 280 × 200 × 90 | 4 | 8 | about 18 min |
| Brush and lipstick | 340 × 180 × 90 | 5 | 9 | about 21 min |
| Narrow vanity, 5 slots | 360 × 120 × 100 | 5 | 9 | about 20 min |
| Palette organizer, 6 slots | 300 × 160 × 100 | 6 | 10 | about 23 min |
| Long vanity, 6 cells | 380 × 160 × 90 | 6 | 10 | about 23 min |
| Storage box, 7 compartments | 340 × 200 × 90 | 7 | 11 | about 25 min |
| 9-cell grid | 270 × 270 × 100 | 9 | 13 | about 29 min |
On a 40 W CO2 the same boxes take roughly 6 to 12 minutes. The times are estimates from the cut length, so treat them as a planning number, not a promise.
Small caddies for a crowded vanity
If the dressing table is already full, start small. These three boxes have few parts, cut fast and forgive a slightly loose fit.
Two-Section Makeup CaddyOuter size (W × D × H) 260 × 160 × 100 mm (10.24 × 6.30 × 3.94 in)Parts 6Est. time, 10 W diode (3 mm) 13 min 23 sEst. time, 40 W CO2 (3 mm) 5 min 35 sSVG · DXF →
The simplest box in the set: one wide section and one narrow one, six parts in total. It is a perfect first project if you have never assembled a tab-and-slot box, and the narrow side holds a brush cup or mascaras upright.
Slanted Makeup Organizer, 3 SectionsOuter size (W × D × H) 280 × 160 × 100 mm (11.02 × 6.30 × 3.94 in)Parts 7Est. time, 10 W diode (3 mm) 16 min 03 sEst. time, 40 W CO2 (3 mm) 6 min 41 sSVG · DXF →
Three equal sections side by side and a 60 mm front, so the sides slope down towards you. Good for a person who keeps three "families": face, eyes, lips.
Square Makeup Organizer, 4 CellsOuter size (W × D × H) 220 × 220 × 90 mm (8.66 × 8.66 × 3.54 in)Parts 8Est. time, 10 W diode (3 mm) 17 min 22 sEst. time, 40 W CO2 (3 mm) 7 min 14 sSVG · DXF →
A 2 × 2 grid in a 220 mm square, the most compact footprint in the set. It slides into a corner of the vanity and still gives four separate homes.
Pro tip: cut the smallest box first in the thickness you plan to use for the whole set. It tells you in 15 minutes whether your kerf and slots fit before you spend a full sheet.
Organizers for brushes and lipsticks
Brushes want height, lipsticks want small cells or a ledge. These three files are built around exactly that.
Brush and Lipstick Makeup OrganizerOuter size (W × D × H) 340 × 180 × 90 mm (13.39 × 7.09 × 3.54 in)Parts 9Est. time, 10 W diode (3 mm) 20 min 57 sEst. time, 40 W CO2 (3 mm) 8 min 44 sSVG · DXF →
A brush column, a wide palette bay and three stepped lipstick cells in one 340 mm box. If you only cut one organizer from this list, this is the most "complete" one.
Makeup Organizer with Lipstick LedgeOuter size (W × D × H) 280 × 200 × 90 mm (11.02 × 7.87 × 3.54 in)Parts 7Est. time, 10 W diode (3 mm) 16 min 59 sEst. time, 40 W CO2 (3 mm) 7 min 05 sSVG · DXF →
Two deep bays at the back and a long front ledge where lipsticks lie flat, labels up. You read every shade without lifting a single tube.
Tiered Makeup Organizer, 3 RowsOuter size (W × D × H) 280 × 220 × 90 mm (11.02 × 8.66 × 3.54 in)Parts 7Est. time, 10 W diode (3 mm) 18 min 50 sEst. time, 40 W CO2 (3 mm) 7 min 51 sSVG · DXF →
Three full-width rows that step down from the 90 mm back to a 50 mm front, like seats in a small theatre: tall brushes at the back, lipsticks in the middle, flat items in front.
Palette organizers
Eyeshadow palettes are flat, wide and always end up in a pile. Standing them upright like files changes everything.
Six-Slot Makeup Palette OrganizerOuter size (W × D × H) 300 × 160 × 100 mm (11.81 × 6.30 × 3.94 in)Parts 10Est. time, 10 W diode (3 mm) 23 min 19 sEst. time, 40 W CO2 (3 mm) 9 min 43 sSVG · DXF →
Six narrow slots in one row: palettes and compacts stand on edge, and you pull out the one you need without moving the rest.
Makeup Palette Tray with 3 Side CellsOuter size (W × D × H) 280 × 200 × 90 mm (11.02 × 7.87 × 3.54 in)Parts 8Est. time, 10 W diode (3 mm) 18 min 00 sEst. time, 40 W CO2 (3 mm) 7 min 30 sSVG · DXF →
One big open area on the left for palettes lying flat, three small cells on the right for the tools you use with them.
Long organizers for a shelf or a mirror cabinet
Narrow boxes live on a bathroom shelf, under a mirror or along the back of a vanity.
Narrow Makeup Vanity Organizer, 5 SlotsOuter size (W × D × H) 360 × 120 × 100 mm (14.17 × 4.72 × 3.94 in)Parts 9Est. time, 10 W diode (3 mm) 19 min 38 sEst. time, 40 W CO2 (3 mm) 8 min 11 sSVG · DXF →
Only 120 mm deep and 360 mm long, five slots in a single row. It fits shelves where a regular organizer hangs over the edge.
Long Makeup Vanity Organizer, 6 CellsOuter size (W × D × H) 380 × 160 × 90 mm (14.96 × 6.30 × 3.54 in)Parts 10Est. time, 10 W diode (3 mm) 22 min 51 sEst. time, 40 W CO2 (3 mm) 9 min 31 sSVG · DXF →
The longest box in the set: two full-depth bays at the ends for tall bottles and four small cells in the middle for everything that rolls.
Big grids for a full collection
When the collection is bigger than a single drawer, go for many cells.
Makeup Storage Box, 7 CompartmentsOuter size (W × D × H) 340 × 200 × 90 mm (13.39 × 7.87 × 3.54 in)Parts 11Est. time, 10 W diode (3 mm) 24 min 54 sEst. time, 40 W CO2 (3 mm) 10 min 22 sSVG · DXF →
One full-depth column for a brush cup and palettes plus six small cells in two rows. A balanced box for a person who uses a bit of everything.
Large 9-Cell Makeup Grid OrganizerOuter size (W × D × H) 270 × 270 × 100 mm (10.63 × 10.63 × 3.94 in)Parts 13Est. time, 10 W diode (3 mm) 28 min 31 sEst. time, 40 W CO2 (3 mm) 11 min 53 sSVG · DXF →
Nine cells in a 3 × 3 grid with three stepped rows, each cell about 9 cm square. Thirteen parts make it the biggest project here: the layout is about 1100 × 469 mm, so most desktop lasers cut it in two or three runs.
Which plywood thickness to choose
Every download has four versions. They are not interchangeable: the slots are drawn for one sheet thickness, so cut the file that matches the sheet you really have.
| Thickness | Look | When to choose it |
|---|---|---|
| 3 mm | Light and delicate, thin dividers | Small boxes, a first project, a 10 W diode laser |
| 4 mm | A bit sturdier, still light | Boxes that will be picked up and moved every day |
| 5 mm | Solid walls, thicker edges | Bigger grids, heavier bottles |
| 6 mm | Chunky, furniture feel | Big boxes and a CO2 laser; on a diode expect several passes |
Measure your sheet with calipers before you cut: "3 mm" plywood is often 2.7–3.2 mm in reality. Our guides on laser power for 3 mm plywood and how many passes 6 mm plywood needs help with the settings.
Common mistake: cutting the 3 mm file from a sheet that measures 3.3 mm. The tabs will not go into the slots, and people blame the file. Measure first, then choose the version, then do one test joint from scrap.
How to cut and assemble a makeup organizer
- Measure the plywood and download the matching thickness version.
- Cut one tab and one slot from scrap and check the fit. If it is too loose or too tight, read about kerf and adjust.
- Cut the parts. Long layouts can be split into runs that fit your bed.
- Sand the edges lightly and remove the smoke marks around the cuts.
- Assemble the dividers into the base first, then add the back, the sides and the front.
- Add a drop of wood glue to the outer corners if the box will be carried around.
- Finish with a clear lacquer or a water-based varnish so powder and spilled foundation wipe off.
Pro tip: a damp cloth removes powder from bare plywood, but liquid foundation leaves a stain. Two thin coats of clear varnish solve that for good.
If you want a lid or a box of your own size, the finger joint box guide shows how to draw one. For rings and earrings, look at the jewelry organizers; for bottles and jars, the skincare organizers.
Next step: pick the box that matches the space on your vanity, measure your plywood and cut the test joint today. Twenty minutes later you will have your first organizer standing on the table.
Questions and answers
What size should a laser cut makeup organizer be?
Most vanity organizers are 220–380 mm wide, 120–270 mm deep and 90–100 mm tall at the back. Measure the free space on the table or shelf and pick a box at least 2 cm smaller in each direction.
What thickness of plywood is best for a makeup organizer?
3 or 4 mm plywood is enough for small boxes and cuts easily on a diode laser. For big grids or heavy bottles, 5–6 mm is sturdier. Always cut the file version that matches your measured sheet thickness.
Can I cut these organizers on a 10 W diode laser?
Yes. In 3 mm plywood they take about 13–29 minutes each. Long layouts need two or three runs on a small bed, and 6 mm plywood usually needs several passes on a diode.
Do I need glue to assemble a tab-and-slot organizer?
No, a good fit holds the box together. A drop of wood glue on the outer corners makes it stronger if the organizer will be carried or moved often.
How do I protect a plywood makeup organizer from stains?
Sand the edges and apply two thin coats of clear water-based varnish or lacquer. Bare plywood soaks up liquid foundation and oil.