VisualizationTiered Makeup Organizer SVG, Three Row Stepped Cosmetic Display Laser Cut File, Wooden Makeup Stand DXF
A free laser cut tiered makeup organizer with three full-width rows, 280 × 220 × 90 mm (11.02 × 8.66 × 3.54 in). Its 7 parts join by tabs and slots, the download offers SVG and DXF for 3 mm, 4 mm, 5 mm and 6 mm plywood, and two cross dividers of different heights make the rows step down from the 90 mm back to the 50 mm front. Free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 220 × 90 mm (11.02 × 8.66 × 3.54 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,020 × 322 mm
- Cut length
- 5.65 m
- Est. time, 10 W diode (3 mm)
- 18 min 50 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 51 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood and cut one long slot test; long dividers bind if the slot is even slightly tight.
- 02Cut the seven parts, putting the two 280 mm cross dividers on a separate sheet if your bed is short.
- 03Insert the 76.5 mm divider at the back and the 63 mm divider in front, add the back wall, slide on the sides and close with the 50 mm front.
- 04Seal it, then fill the rows from back to front: tall items, compacts, flat palettes.
Three rows like a small display stand
Unlike the boxes with side-by-side cells, this one has no front-to-back dividers at all. Two long cross dividers run the full 280 mm width: the rear one is 76.5 mm tall, the front one 63 mm. Together with the 90 mm back and the 50 mm front they form three rows that drop like steps. The photo, taken next to a stone basin, shows brushes and lipsticks in the back row, two round compacts in the middle and palettes in the low front row, so every lid faces you.
Cutting and putting it together
Seven parts nest on a 1020 × 322 mm sheet. The cross dividers are 280 mm long, as long as the base, so on a small bed place them on their own sheet. The 3 mm file takes about 18 min 50 s on a 10 W diode, about 7 min 51 s on a 40 W CO2 and about 3 min 46 s on a 100 W CO2. A diode handles 3 mm in one or two passes; for 5 or 6 mm stock run several passes or use a CO2.
Slot both cross dividers into the base, taller one at the back, then add the back wall and slide the sloped sides over the divider ends. The front goes on last. The long dividers brace the sides, so the box is stiff even without glue.
Where it works best
The stepped rows suit a shop counter or a makeup studio where products should be seen, not hidden. For a bathroom, seal it with two coats of lacquer. Craft sellers can list it as a lipstick display stand and photograph it filled, or make a larger copy for a nail polish rack.
Questions about this file
How deep is each of the three rows?
The 220 mm depth is shared between three rows, so each is roughly 7 cm deep. That fits brushes upright, compacts and palettes standing at a slight angle.
Can I use it as a lipstick display at a market stall?
Yes, the stepped rows show dozens of lipsticks or nail polishes with labels facing out. Cut it from 4 mm for extra stiffness when it is moved often.
Is it possible to make it wider?
Lengthen the base, front, back and both cross dividers by the same amount, and keep the slot widths unchanged. The sides stay as they are.
Can I glue it?
The long dividers make it rigid without glue, but a line of wood glue along the base slots is fine if it will carry heavy glass bottles.
How do I make it safe next to a wet sink?
Coat all surfaces, including the slot edges, with water-based polyurethane before assembly. That keeps the plywood from swelling around the joints.
Similar files
