VisualizationBrush and Lipstick Organizer SVG, Makeup Vanity Box With Stepped Cells Laser File, Wooden Palette Holder DXF
A free download for a makeup organizer with a brush column, a wide palette bay and three stepped lipstick cells, 340 × 180 × 90 mm (13.39 × 7.09 × 3.54 in) in all. Nine plywood parts join with tabs and slots, the sides slope from a 90 mm back to a 54 mm front, and SVG and DXF files are included for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 180 × 90 mm (13.39 × 7.09 × 3.54 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,060 × 282 mm
- Cut length
- 6.28 m
- Est. time, 10 W diode (3 mm)
- 20 min 57 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 44 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick your plywood file and test-cut one of the short cross-divider slots.
- 02Cut the nine parts from the 1060 × 282 mm layout, separating the long pieces on a small bed.
- 03Fit both long dividers, add the 77.8 mm cross divider behind the 65.6 mm one in the right column, then close with back, sides and front.
- 04Seal it, put a brush cup in the left column, palettes in the center and lipsticks in the stepped cells.
Three zones in one box
Two long dividers split the 340 mm length into three columns of different use. The narrow left column runs the full depth and is sized for a brush cup; in the photo a cut-glass tumbler holds five brushes. The wide center bay is open, with room for an eyeshadow palette, a large powder and a blush. The right column, about 10 cm wide, is divided by two short cross dividers into three small cells. Their heights differ (77.8 mm at the back, 65.6 mm in front), so the cells step down like a small staircase: a cream compact at the back, a lipstick lying down in the middle and two lipsticks standing in front.
Cutting it
The 3 mm layout is 1060 × 282 mm; on a smaller bed, separate the base and the two 340 mm walls from the rest. Expect about 20 min 57 s for the 3 mm file on a 10 W diode, about 8 min 44 s on a 40 W CO2 and about 4 min 11 s on a 100 W CO2. 3 mm cuts in one or two diode passes; 5 and 6 mm call for a CO2 or repeated slow passes.
Assembly, finish and ideas
Place both long dividers in the base, drop the two cross dividers into the right column with the taller one at the back, then fit the back, sides and the 54 mm front. Tabs hold it dry; glue them if you prefer a permanent box. Sand and seal with lacquer, especially the brush column if you rinse brushes and put them back damp.
The three zones make it a good starter organizer for a teenager, a gift with a matching glass brush cup, or a shop item photographed fully stocked.
Questions about this file
What size brush cup fits the left column?
A glass or jar up to about 7 cm across fits comfortably. Measure your cup first, because the column width also depends on the plywood thickness.
Why are the lipstick cells stepped?
The cross dividers follow the slope of the sides, 77.8 mm at the back and 65.6 mm in front, so every cell stays visible from above.
Can I flip the layout to put brushes on the right?
Yes, mirror the base, the long dividers and the front and back in your editor before cutting. The tabs still line up after mirroring.
What if I scale it down to fit a small shelf?
Shrink only the outline and keep the slots at your exact plywood thickness. Scaling everything makes the slots too narrow to assemble.
Is lacquer or oil better around wet brushes?
Lacquer seals better against water, which matters in the brush column. Oil looks warmer but needs a fresh coat every few months.
Similar files
