VisualizationSlanted Makeup Organizer SVG, Three Section Vanity Box Laser Cut File, Wooden Lipstick and Brush Holder DXF
A free laser cut file for a slanted makeup organizer with three equal side-by-side sections, 280 × 160 × 100 mm (11.02 × 6.30 × 3.94 in) outside. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the 7 pieces join with tabs and slots, and the front is only 60 mm high so the sides slope down toward you. The file costs nothing to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 160 × 100 mm (11.02 × 6.30 × 3.94 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 900 × 272 mm
- Cut length
- 4.82 m
- Est. time, 10 W diode (3 mm)
- 16 min 03 s
- Est. time, 40 W CO2 (3 mm)
- 6 min 41 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the SVG or DXF for your plywood (3, 4, 5 or 6 mm) and cut a single slot on scrap to confirm the tabs press in snugly.
- 02Cut the seven parts from the 900 × 272 mm layout, splitting it across two sheets if your bed is shorter.
- 03Fit both dividers into the base, add the 100 mm back, press on the sloped sides and finish with the 60 mm front.
- 04Sand the edges, seal with lacquer or oil, then load palettes on the left, brushes in the middle and lipsticks on the right.
Three bays for three kinds of makeup
Two long dividers run from the back wall to the front and split the 280 mm length into three equal bays. On the vanity in the photo the left bay holds eyeshadow palettes and powder compacts standing on edge, the middle one keeps brushes upright, and the right one lines up lipsticks. The 100 mm back hides the brush handles, while the 60 mm front lets you read every shade label without lifting anything out.
Cutting it on a hobby laser
All seven parts sit on a 900 × 272 mm layout. If your bed is shorter than 900 mm, move the base and the back panel to a second sheet and cut the rest on the first. A 10 W diode handles 3 mm birch in one or two passes, and the estimate is about 16 min 03 s for the 3 mm file on that machine, about 6 min 41 s on a 40 W CO2 and about 3 min 13 s on a 100 W CO2. The 5 and 6 mm files make heavier walls but need a stronger tube or several slow passes on a diode.
Assembly and finish
Push both dividers into the base first, add the back, slide on the two sloped sides and close it with the low front. The tab joints hold on their own; a drop of wood glue per tab makes the box permanent. Sand off the scorch marks and wipe on clear lacquer or hardwax oil if the box will stand near a sink.
Ideas for gifts and shop listings:
- A first makeup kit for a teenager, packed into the three bays
- An Etsy listing offered in natural birch and in a walnut stain
- A bridesmaid box with her lip color waiting in the right-hand bay
Questions about this file
Will a standard eyeshadow palette fit in one bay?
Each bay is a little under 9 cm wide and runs the full 16 cm depth, so quads, compacts and most slim palettes stand on edge without trouble. Wide 12-pan palettes are better kept flat in a drawer.
Can I make the box longer for a bigger dresser?
Yes, stretch only the outer dimensions in your editor and keep every slot exactly as wide as your plywood. Scaling the whole drawing also widens the slots, and the tabs will rattle.
Which plywood thickness works best for this three-bay box?
3 mm keeps it light and quick on a 10 W diode, 4 mm feels noticeably stiffer, and 5–6 mm gives chunky walls that look good in product photos.
Can I put it on a bathroom counter?
Only after sealing every face, including the underside of the base, with two coats of clear lacquer or a water-resistant oil. Bare birch soaks up splashes and swells.
Is there room to engrave a name?
The file contains cut lines only, but the 280 mm wide front panel takes a name or monogram well. Add an engrave layer in your laser software before you cut.
Similar files
