VisualizationMakeup Organizer With Lipstick Ledge SVG, Three Compartment Vanity Box Laser File, Wooden Brush Holder DXF
A free download for a makeup organizer with three compartments: two deep back bays and a long front ledge where lipsticks lie flat. It measures 280 × 200 × 90 mm (11.02 × 7.87 × 3.54 in), is cut from 7 plywood parts joined with tabs and slots, slopes from a 90 mm back to a 50 mm front, and includes SVG and DXF files for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 200 × 90 mm (11.02 × 7.87 × 3.54 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 980 × 302 mm
- Cut length
- 5.09 m
- Est. time, 10 W diode (3 mm)
- 16 min 59 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 05 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the 3, 4, 5 or 6 mm file and test the cross-divider slot on scrap first.
- 02Cut the seven parts from the 980 × 302 mm nest.
- 03Hook the short divider onto the 65.8 mm cross divider, set both in the base, then add back, sides and the 50 mm front.
- 04Lacquer the ledge and inside, then lay lipsticks on the ledge and fill the two back bays.
Two bays and a lipstick ledge
A full-length cross divider, 65.8 mm tall, sits about 7 cm behind the front wall and creates a long, shallow ledge across the whole 280 mm. Lipsticks lie side by side there with their labels up, together with a highlighter or a small compact; the photo shows two lipsticks and a powder lined up on it. Behind the cross divider, one short divider splits the deep back area into two bays: a brush cup and a compact on the left, stacked eyeshadow and blush palettes on the right.
Cutting and assembly
Only seven parts, nested on 980 × 302 mm. If the bed is shorter, cut the base and cross divider on a separate sheet. The estimate for the 3 mm file is about 16 min 59 s on a 10 W diode, about 7 min 05 s on a 40 W CO2 and about 3 min 24 s on a 100 W CO2. For 5 or 6 mm stock on a diode, expect several passes and slower speeds.
Slot the short divider into the cross divider, set both in the base, then add the back, the sloped sides and the 50 mm front. Glue is optional; a small bead along the cross divider stops the ledge from flexing if you lean on it.
Finishing and uses
Sand lightly and seal the ledge with lacquer, because lipstick smears show on bare birch. Besides makeup, this layout works for a skincare routine (tubes on the ledge, jars behind), for watches and bracelets, or as a desk organizer with pens on the ledge. For a gift, put three lipsticks on the ledge and a brush set in the back bay.
Questions about this file
How many lipsticks fit on the front ledge?
Lying flat, about eight to ten standard lipsticks fit along the 280 mm ledge, or fewer if you mix in a compact.
Can lipsticks stand upright instead?
Yes, in the back bays, which are deep enough for tubes to stand behind the 65.8 mm cross divider.
Can I scale it for tall perfume bottles?
Raise the height in your drawing but keep slot widths and tab sizes matched to your plywood. Scaling the file proportionally would make the slots too wide.
What finish keeps lipstick from staining?
A hard clear lacquer works better than oil, since lipstick wax wipes off a sealed surface. Two coats are enough.
Is this a good box to engrave?
The 280 mm front gives room for a name, and the ledge itself can carry a fine line pattern. Add the engraving layer yourself before cutting.
Similar files
