DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
MDF dog bed with a wavy back, low front with a bone shape and bone hand holes in the sides, cushion inside, on a wooden floor by a sofaVisualization
DW-300030 · UPDATED 11/21/2026

Wooden Dog Bed DXF, Bone Cutout Pet Bed SVG, Small Dog Bed Laser Cut File, Cat Bed Plans

A tab-and-slot wooden bed for a cat or small dog, with a tall wavy back, a low front for easy stepping in, two sides with bone-shaped hand holes and a bone motif on the front. It downloads free as an SVG and a DXF holding every part on a 690.9 × 621 mm (27.20 × 24.45 in) layout, cut lines only; the slots in the file are 6 mm wide.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
691 × 621 mm (27.20 × 24.45 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
8.63 m
Est. time, 10 W diode (3 mm)
28 min 46 s
Est. time, 40 W CO2 (3 mm)
11 min 59 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Measure your sheet, then cut a single tab and slot from it and adjust the kerf until they slide together firmly.
  2. 02Cut the base, back, front, two sides and the bone shape on a bed of at least 60 × 40 cm.
  3. 03Stand the back and the two sides on the base tabs first, then push the low front into place and add the bone.
  4. 04Glue the slots if you want it rigid, sand the edges round, paint or oil it and add a cushion.

What is in the layout

The base is a rectangle of about 510 × 310 mm with tabs along every edge. Around it sit the back panel with a wavy top edge, a low front panel with a dip in the middle so an older pet can walk in, two side panels with wavy edges and a bone-shaped hand hole each, and a loose bone shape for the front. The tabs of the base drop into long slots in the four walls, so the bed holds together without screws or hardware. The photo shows it in plain MDF on a living-room floor with a flat cushion inside.

Material and cutting

Every slot measures 6 mm, so pick 6 mm plywood or MDF and cut one slot and one tab first: sheet that is really 5.6 or 6.3 mm needs a small kerf change. Do not scale the file to make a bigger bed unless you also change the slot width. The whole layout is close to 70 × 62 cm, which is larger than most hobby diode beds; the base alone needs about 51 × 31 cm, so a 60 × 40 cm laser or a CNC router is the minimum. Birch plywood holds up better than MDF if a dog chews or scratches.

Finishing and selling

Round over the wavy edges and the hand holes with sandpaper so nothing snags fur. A drop of wood glue in each slot turns it into a solid piece of furniture. Paint the bone white or engrave a pet name on the back panel before assembly. Pet beds sell well at local markets as a set with a matching food bowl stand or a name sign for the kennel.

Questions about this file

What size pet does it fit?

The base is about 51 × 31 cm, which suits a cat, a toy breed or a puppy. For a larger dog, redraw the slots for your sheet before you enlarge it.

Which sheet thickness do the joints need?

The slots are drawn 6 mm wide. Use 6 mm plywood or MDF and test one joint, since real sheets vary a little.

Can I cut it on a 40 × 40 cm laser bed?

Not as drawn. The base and the back are both about 51 cm long, so you need a larger bed or a CNC router.

Is MDF safe for a pet bed?

Sealed MDF works indoors, but it swells if it gets wet and dogs can chew it. Plywood with a water-based clear coat lasts longer.

Can I add my dog's name?

Yes. Add an engraving layer with the name on the back panel or the bone in your laser software before cutting.

Similar files