DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Round wall piece with cream petals inlaid in a black disc inside a white ring, hanging on a cream wall next to a plantVisualization
DW-300015 · UPDATED 11/20/2026

Flower Wall Art SVG, Round Petal Inlay Laser Cut File, Two Tone Flower Wall Decor DXF, Boho Flower Disc Cutout

A round flower design with eight large pointed petals, eight small teardrop petals and a round center inside a thin outer ring. The free SVG and DXF hold cut lines only at 304.8 × 304.8 mm (12 × 12 in); one cut gives the ring, a disc with 17 flower-shaped windows, and the 16 petals and the center as loose pieces for a two-tone inlay.

Author
DXF World · 415 files
Formats
SVG, DXF
Size
305 × 305 mm (12.00 × 12.00 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
4.43 m
Est. time, 10 W diode (3 mm)
14 min 46 s
Est. time, 40 W CO2 (3 mm)
6 min 09 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the size, then cut the file once in a dark sheet and once in a light sheet.
  2. 02Cut a plain backing circle matching the outer edge of the ring.
  3. 03Glue the dark disc to the backing and press the light petals and center into its windows.
  4. 04Glue on the ring, sand the faces flush, seal, and fit a hanger on the back.

What you get from one cut

Cutting the file once leaves three groups of parts. The outer ring is a thin band that frames the piece. Inside it is a disc with 17 windows: eight long pointed petals on the outside, eight small teardrops in an inner ring, and a circle in the middle. The third group is the drop-outs from those windows, which are the petals and the center themselves. No petal touches another, so the disc stays strong and every piece comes out clean.

Making the two-tone version

The photo shows the classic use: cream petals set flush into a black disc, framed by a white ring. Cut the file twice, once in a dark sheet and once in a light one, then swap the parts and fit the light petals into the dark disc. The laser removes a thin line of material, so the inlays sit slightly loose; glue the disc to a plain backing circle and press each petal in with a dab of glue. You can also skip the inlay and glue the petals straight onto a painted round board for a raised, layered flower.

Scaling and finishing

The design has no thin bridges apart from the ring, so it scales freely, from a 15 cm plaque to a 60 cm piece cut on a CNC router. Sand the petal edges before fitting them. It suits a boho living room above a sofa, a nursery wall in pastel colours, a set of three in different sizes, or a Mother's Day present in her favourite colours.

Questions about this file

Why does the file give a ring and a separate disc?

A cut line runs between them, so you can make the ring in a third colour, like the white edge in the photo.

Will the petals fit snugly?

They sit slightly loose because of the kerf. A backing board and glue hold them; for a tighter fit, offset the petal outlines outward by half the kerf.

Can I make it without the inlay?

Yes. Glue the petals and center straight onto a painted board for a raised flower, and keep the disc as a stencil.

Does the thin ring break when scaled down?

Below about 15 cm the ring gets fragile. Widen it in your software or leave it out for small versions.

Which materials look good together?

Black and natural birch plywood, walnut and maple, or mirror and black acrylic all give strong contrast.

Similar files