DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Black metal silhouette of a cowboy and a cowgirl holding a lasso rope between them, bolted to a base plate on a wooden tableVisualization
DW-300067 · UPDATED 11/21/2026

Cowboy and Cowgirl Silhouette SVG, Western Couple With Lasso Laser Cut File, Ranch Wedding Decor DXF, Rodeo Sign

A western couple silhouette: a cowboy in a wide hat holding one end of a lasso rope, and a cowgirl in a flat-brimmed hat and long skirt holding the other end, with a coil of rope looped over her arm. The free download is one SVG and one DXF file, 497.8 × 406.4 mm (19.60 × 16.00 in), cut lines only, in one piece because the rope joins the two figures.

Author
DXF World · 530 files
Formats
SVG, DXF
Size
498 × 406 mm (19.60 × 16.00 in)
Material
Plywood, MDF, acrylic or metal (scale to your piece)
Cut length
4.07 m
Est. time, 10 W diode (3 mm)
13 min 34 s
Est. time, 40 W CO2 (3 mm)
5 min 39 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Decide whether the piece will stand, hang or sit on a backer, and add a base strip under the boots if it will stand.
  2. 02Scale it to your size and check the rope width, thickening it if your material is brittle.
  3. 03Cut the silhouette, then the base plate or backer from the same or a contrasting material.
  4. 04Finish with paint, stain or a rust patina, then bolt or glue the couple to the base and add names if you like.

The design

The cowboy stands on the left in boots, jeans and a wide-brimmed hat, both hands on the rope. The cowgirl on the right leans back slightly in a long skirt and boots, one hand on the rope and the other holding a loose coil of three loops. The file has only seven contours, so it is clean and quick: one outer line that runs around both figures and the straight rope between them, plus the openings inside the coil and a small gap at her wrist. The photo shows it in black steel bolted to a long base plate on a dining table.

Making it strong

The rope between the two hands is the narrowest part, only a few millimetres wide at the drawn size. Three ways to deal with it:

  • Cut a base plate or strip under the boots, as in the photo, so the rope carries no weight.
  • Glue the piece onto a backer board for a wall sign.
  • Thicken the rope line a little in your software before cutting.

At 500 mm wide it suits 3–6 mm plywood or MDF on a laser with a large bed, 1.5–2 mm steel on a plasma table, or 12 mm board on a CNC router for outdoor use.

Gift and selling ideas

  • Ranch or country wedding decor: add the couple's names and date on the base plate.
  • Anniversary gift for a horse-loving couple.
  • Porch or barn sign in rusted steel.
  • A smaller 250 mm version as a cake topper in gold acrylic.

Questions about this file

Is it one piece?

Yes. The lasso rope connects the two figures, so both come out of the sheet together.

Does the file include the base in the photo?

No, the base plate is not in the file. Draw a simple rectangle under the boots or use a wooden board.

Can I use it as a wedding cake topper?

Yes, scaled to about 200–250 mm wide in 3 mm acrylic, with two picks glued under the boots.

Will the rope break?

In plywood at small sizes it can. Support it with a base or backer, or thicken the rope before cutting.

Which way do the figures face?

Toward each other: the cowboy on the left, the cowgirl on the right. Mirror the file if you need them the other way.

Similar files