DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Birch plywood box with its lift-off lid leaning against it, three compartments holding white napkins, cork coasters, metal straws and toothpicks on a counterVisualization
DW-105041 · UPDATED 11/16/2026

Napkin Box With Lid SVG, Lift Off Lid Storage Box Laser File, Wooden Table Setting Organizer DXF

A free three-compartment napkin storage box with a separate flat lid that simply sits on top, for napkins, coasters, straws and picks. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 260 × 160 × 80 mm (10.24 × 6.30 × 3.15 in) and has 8 pieces that fit together with tabs and slots.

Author
DXF World · 281 files
Formats
SVG, DXF
Outer size (W × D × H)
260 × 160 × 80 mm (10.24 × 6.30 × 3.15 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
860 × 252 mm
Cut length
7.58 m
Est. time, 10 W diode (3 mm)
25 min 16 s
Est. time, 40 W CO2 (3 mm)
10 min 32 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the file for the plywood you have, and cut one tab with its slot from scrap to test the fit.
  2. 02Cut the 8 parts from the 860 × 252 mm sheet or across two shorter boards.
  3. 03Join the base, front, back and sides, push the two dividers home, then lay the lid on top and check it sits flat.
  4. 04Sand the wall tops smooth, oil or lacquer every piece including the lid, and pack in napkins, coasters and straws.

A lid you just lift away

The lid is one 260 × 160 mm panel, the full footprint of the box. It rests on the four walls, and the two dividers are cut 3 mm lower than the walls so it lies flat. Lift it off and set it aside, or lean it against the back as in the photo. With nothing to slide or swing, this is the quickest lidded box in the set to build, and the lid can double as a small serving board or a coaster tray.

Layout and contents

The inside is split left to right into three compartments. The left one holds a pile of white beverage napkins lying flat, the centre one a tall stack of round cork coasters, and the right one a mix of metal chopsticks or straws and a glass of toothpicks. Put the box in a drawer between parties, or leave it on the dining table with the lid off when guests arrive.

Making it

With the 3 mm file, cutting takes about 25 min 16 s on a 10 W diode, about 10 min 32 s on a 40 W CO2 and about 5 min 03 s on a 100 W CO2. The pieces are laid out on 860 × 252 mm; split them over two sheets if your laser is smaller. A 10 W diode cuts 3 mm in one or two passes, but 5 and 6 mm boards need several passes or a CO2 tube.

Build the base and walls first, slide the dividers into their slots, and check that the lid sits evenly before adding glue. Sand the top edges of the walls so the lid does not catch. Finish with Danish oil for a warm tone, or with clear lacquer to keep the birch pale.

Engrave a monogram on the lid and fill the box with linen napkins for a wedding or anniversary gift.

Questions about this file

Does the lid lock in place?

No, it is a loose panel that rests on the walls. That makes it easy to open with one hand at the table.

Why are the dividers shorter than the walls?

They are 77 mm tall against 80 mm walls, so they stay just below the lid and do not hold it up.

Can I add a handle or knob to the lid?

Yes, drill a small hole and screw on a wooden knob, or glue a short strip of plywood across the lid as a pull.

Can the box live under a kitchen sink?

Coat every face, edges included, with two layers of polyurethane. Raw plywood swells if it stays damp.

Will it work as a tea or sugar box?

The three sections also suit tea bags and sugar sachets, and the lid keeps out dust. Line the base with paper for loose items.

Similar files