VisualizationSliding Lid Box SVG, Olive Oil Gift Box Laser Cut File, Wooden Sauce Bottle Storage DXF
A free laser cut file for a wooden box with a sliding lid and three sections side by side, sized for small bottles of oil, vinegar and hot sauce. You get SVG and DXF with a separate version for 3, 4, 5 and 6 mm plywood; the 10 pieces (four walls, base, two dividers, two rails and the lid) fit together with tabs and slots into a 280 × 160 × 80 mm (11.02 × 6.30 × 3.15 in) box.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 160 × 80 mm (11.02 × 6.30 × 3.15 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 926 × 416 mm
- Cut length
- 7.15 m
- Est. time, 10 W diode (3 mm)
- 23 min 50 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 56 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Open the folder for your plywood thickness and cut a rail and a short slot on scrap to see that the lid will glide.
- 02Cut the 10 parts; keep the lid flat on the bed and cut it last so it does not shift.
- 03Build base, back, sides and dividers, fit the two rails, slide the lid in, and only then add the front wall.
- 04Wax the rails, lacquer the outside and fill the three bays with small bottles before closing the lid.
Inside the box
Two dividers split the interior into three long bays. The photo shows a hot sauce, a bottle of olive oil and a dark balsamic each resting in its own bay, with the lid pushed halfway so you can see what is stored. Miniature 100 ml bottles and small jam jars are the right scale here, which makes it a natural tasting set rather than everyday pantry storage.
How the lid works
The lid is a flat panel of 273.4 × 159.7 mm that slides in on two narrow rails near the top of the walls. There is no hinge and no lock: pull it back to open, push it home to close. The front wall is 73.7 mm, a little shorter than the 80 mm back, so leave it until the rails and lid are in place and test the slide before gluing anything. If the lid binds, a few strokes of sandpaper along its edges or a rub of candle wax on the rails cures it.
Time, sheet and finish
For the 3 mm file, expect about 23 min 50 s on a 10 W diode, about 9 min 56 s on a 40 W CO2 and about 4 min 46 s on a 100 W CO2. The full layout is 926 × 416 mm; most hobby beds need it spread over two or three sheets, with the lid on its own. A 10 W diode handles 3 mm in one or two passes, while 5 and 6 mm plywood want a CO2 or patient extra passes.
The lid is the best place for decoration. A deli or olive oil shop can engrave its logo there and fill the box as a ready gift; at home it makes a neat present for someone who cooks. Finish with clear lacquer so an oily thumbprint wipes straight off.
Questions about this file
What size bottles does this sliding lid box take?
With an inside height a little under 80 mm, it suits miniature oil and vinegar bottles, small hot sauces and squat jars. Tall 500 ml bottles will not fit under the lid.
Why does my lid stick halfway?
Plywood often runs slightly thicker than its label, which pinches the lid between the rails. Sand the lid edges lightly or cut the file one thickness size up.
Should the rails be glued?
A small dot of wood glue on each rail keeps them from creeping out after many openings. Keep glue away from the lid so it still slides.
Can I engrave a logo or a name on the lid?
Yes, add an engraving layer to the lid in your laser software; the download itself has cut lines only. Engrave before cutting so the panel stays registered.
Which plywood thickness is best for a gift box?
3 mm birch keeps the box light and cuts fastest, while 4 mm feels sturdier in the hand. Both slide smoothly when the file matches the sheet.
Similar files



