VisualizationSliding Lid Cutlery Box SVG, Wooden Flatware Storage Box Laser Cut File, Silverware Chest With Lid DXF
A square cutlery box with a sliding lid that runs in on two rails, and two sections inside for flatware and chopsticks. It measures 280 × 280 × 60 mm (11.02 × 11.02 × 2.36 in), is made of 9 plywood pieces joined with tabs and slots, and is a free SVG and DXF download with a separate file for 3, 4, 5 and 6 mm plywood. There is no hinge and no lock.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 280 × 60 mm (11.02 × 11.02 × 2.36 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,140 × 636 mm
- Cut length
- 8.71 m
- Est. time, 10 W diode (3 mm)
- 29 min 02 s
- Est. time, 40 W CO2 (3 mm)
- 12 min 06 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the thickness folder that matches your plywood and cut a test slot plus a short rail section to check how the lid edge rides.
- 02Cut the base, four walls, divider, two rails and the lid, spreading the two large square panels over separate sheets if needed.
- 03Build the box around the base with the divider in place, then fix the two rails along the inside of the side walls.
- 04Slide the lid in, sand any tight spots on its edges, finish everything with oil or lacquer and load the cutlery.
A covered box for flatware
One long divider runs from front to back and splits the interior into two sections. In the photo the narrow left side is filled with wooden chopsticks, while the wide right side holds forks, spoons and table knives lying next to each other. The lid is a flat panel that slides along two thin rails fixed to the inside of the side walls. The front wall is a little lower than the others, so the lid can slide out over it, and you can leave it half open on the table while serving. A covered box keeps dust off cutlery that lives on an open shelf, in a camper van or in the good-silverware cupboard.
Cutting and fitting the rails
The 3 mm sheet comes to 1140 × 636 mm because the base and the lid are both close to 280 mm square. Each of those big panels fits on its own on a 300 mm bed, so plan three or four small sheets on a compact diode. Expected time for the 3 mm file: about 29 min 02 s on a 10 W diode, about 12 min 06 s on a 40 W CO2, about 5 min 48 s on a 100 W CO2.
Test the lid in the rails before you finish anything. If it binds, sand the lid edges, not the rails; wax on the edges makes it glide.
Gift and shop ideas
- Engrave a monogram or a wedding date on the lid and sell it as a keepsake flatware chest.
- Fill it with a set of chopsticks for a sushi-night gift.
- Offer a walnut-stained version next to the plain birch one.
Questions about this file
How does the lid stay in place without a hinge?
It runs on two rails along the side walls and slides out over the lower front wall. Nothing needs a hinge or a catch.
Is there room for long serving spoons?
The wide section is about 280 mm front to back on the outside, which takes dinner forks and table knives. Big serving spoons or ladles longer than that will not fit.
Can I cut the lid from acrylic so I can see inside?
Yes, a 3 mm clear acrylic lid looks good on a birch box. Cut it from the 3 mm file and check that it slides, since acrylic does not compress like wood.
The lid sticks after finishing. What should I do?
Lacquer adds thickness to the edges. Sand the lid edges back lightly and rub them with paste wax or a candle so the lid moves freely.
Can I put a name on the lid?
The file is cut lines only, but the lid is a large flat panel that is easy to engrave. Add your own text or picture as an engrave layer before cutting.
Similar files



