DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood three-tier tea rack with nine slots holding three gold-lid jars of loose tea on top and rows of green, burgundy, mustard, cream and lilac tea bags below, on a marble kitchen counterVisualization
DW-102062 · UPDATED 11/16/2026

Tiered Tea Rack SVG, Nine Slot Tea Bag Display Laser Cut File, Tea Bar Stand DXF, Wooden Tea Shelf Organizer

A free tiered tea rack with 3 steps rising toward the back and two dividers on each step, giving 9 slots for tea bags and jars. The download holds SVG and DXF files for 3, 4, 5 and 6 mm plywood; the rack measures 290 × 200 × 210 mm (11.42 × 7.87 × 8.27 in) and goes together from 15 pieces with tabs and slots, each marked with a small engraved part number.

Author
DXF World · 281 files
Formats
SVG, DXF
Outer size (W × D × H)
290 × 200 × 210 mm (11.42 × 7.87 × 8.27 in)
Parts
15
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,180 × 337 mm
Cut length
10.09 m
Est. time, 10 W diode (3 mm)
33 min 39 s
Est. time, 40 W CO2 (3 mm)
14 min 01 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Open the folder for your plywood thickness, cut one test slot and confirm the tab fit before you start the long layout.
  2. 02Cut the two stepped sides, three shelves, front board, two step boards, brace and six dividers, spread over two or three sheets.
  3. 03Use the engraved numbers to match parts: shelves and brace into one side, then the second side, the boards, and two dividers per step.
  4. 04Sand, lacquer, and fill the top tier with jars and the lower two with tea bag envelopes.

Nine slots on three tiers

This is the larger of the two tea step stands: 290 mm wide and 210 mm tall, with three slots on every step instead of two. In the photo the top tier carries three gold-lid jars of loose tea, the middle tier shows green, burgundy and mustard tea bag envelopes, and the bottom tier holds cream, sage and lilac ones. Each step rises above the one in front, so every label faces you, and the whole selection reads like a small shop shelf.

The dividers are short, around 38 to 40 mm tall, enough to keep stacks upright without hiding the packets.

Cutting a big layout

At 1180 × 337 mm the full layout is longer than nearly every desktop laser bed, so plan on two or three sheets: the two stepped sides together, the long shelves and boards together, and the six dividers fill the gaps. The 3 mm file takes about 33 min 39 s on a 10 W diode, about 14 min 01 s on a 40 W CO2 and about 6 min 44 s on a 100 W CO2. A 10 W diode does 3 mm in one or two passes; 5 and 6 mm need a more powerful laser or many passes, which adds up on a piece this size.

Every part carries a small engraved number, which helps a lot with fifteen pieces where several shelves look nearly identical. Join the shelves and brace to one side, close with the other side, then add the front and step boards and drop two dividers onto each tier. Glue is optional; a few drops make it rock solid for a busy counter.

For tea bars and shops

  • Engrave your cafe name on the front board and use it as a self-serve tea menu.
  • Offer it on Etsy as a tea bar centerpiece for weddings and showers.
  • Fill all nine slots with samples for a premium gift.

Questions about this file

How does this differ from the six-pocket tea stand?

It is wider and taller and has two dividers per step, so you get nine slots instead of six. Choose it when you want to show more flavors.

Will tea bag envelopes stand up in the slots?

Yes. Each slot is just under a third of the 290 mm width, so standard envelopes stand in stacks and lean back slightly against the step behind.

Can I cut it on a 400 mm bed?

Yes, by splitting the layout across several sheets. The longest pieces are the 290 mm shelves and boards, which fit most beds easily.

What are the small numbers on the parts?

They are engraved part numbers to make assembly easier. Sand them away afterwards if you prefer a clean finish.

Does it need to be waterproofed?

Near a kettle or sink, yes: two coats of clear lacquer protect it from splashes and steam.

Similar files