VisualizationSilverware Box With Lid SVG, Wooden Cutlery Storage Box Laser Cut File, Three Section Flatware Case DXF
A three-section silverware box with a separate lid that lifts off and sits on top, for forks, spoons, knives and chopsticks. It measures 260 × 280 × 60 mm (10.24 × 11.02 × 2.36 in), is made of 8 plywood pieces that fit together with tabs and slots, and comes as a free SVG and DXF download with separate files for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 280 × 60 mm (10.24 × 11.02 × 2.36 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,100 × 352 mm
- Cut length
- 9.22 m
- Est. time, 10 W diode (3 mm)
- 30 min 44 s
- Est. time, 40 W CO2 (3 mm)
- 12 min 49 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the folder for your plywood thickness and check a single tab in its slot on a scrap piece before cutting the full set.
- 02Cut the base, four walls, two dividers and the lid; give the base and lid their own sheets on a small bed.
- 03Assemble the walls on the base, slide in the two lower dividers, then rest the lid on top to make sure it lies flat.
- 04Sand all edges, add any engraving you like to the lid, seal with oil or clear lacquer and load the silverware.
What the lid adds
The lid is a plain flat panel the full size of the box, 260 × 280 mm, and it simply rests on the four walls. There is nothing to slide or swing, so you can lift it off with one hand, lean it against the wall while you lay the table, and drop it back on. The two dividers inside are a touch lower than the outer walls, which lets the lid lie flat. That makes this the easiest of the covered cutlery boxes to build and the one with the fewest parts that can go wrong.
In the photo the three sections hold dinner forks on the left, a stack of spoons in the middle, and table knives with a few chopsticks on the right. Keep it on an open shelf, in a dresser for the best silverware, or in a picnic basket.
Building and cutting
On a 10 W diode the 3 mm file takes about 30 min 44 s, on a 40 W CO2 about 12 min 49 s, and on a 100 W CO2 about 6 min 09 s. The 3 mm parts spread over 1100 × 352 mm, so a small-bed machine needs two or three runs: the base and the lid each take most of a 300 mm sheet. Build the open box first and glue it if you want, then check the lid sits evenly before finishing.
Personal touches
The lid is a blank canvas. Add your own engraving of a family name, a floral border or a simple line drawing of a fork and spoon, then oil the whole box so the engraving darkens nicely. Sold filled with a new cutlery set, it is a practical wedding or anniversary gift.
Questions about this file
Does the lid lock or click into place?
No, it rests on the walls by its own weight. That keeps dust out but means the box should be carried level, holding the lid down.
Why are the inner dividers lower than the walls?
So the lid can lie flat on the outer walls without rocking on them. It also leaves a little space to lift cutlery out by the handles.
Could I make the lid from clear acrylic?
Yes, a 3 mm acrylic lid shows off the contents and wipes clean. The rest of the box can stay plywood, cut from the file for your sheet thickness.
Is this box safe for storing good silver?
Birch plywood is fine once it is sealed. Line the sections with felt or anti-tarnish cloth if you want to protect polished silver from scratches.
What finish suits a box kept on an open shelf?
A satin water-based lacquer keeps the pale wood look and resists dust and fingerprints. Hardwax oil gives a warmer tone and is easy to touch up later.
Similar files



