VisualizationNapkin Organizer SVG, Four Section Table Caddy Laser Cut File, Straw and Toothpick Holder DXF
A free open napkin organizer with four compartments: a napkin section, a coaster section and a right-hand column split into a back pocket for straws and a front pocket for toothpicks. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; it measures 260 × 180 × 80 mm (10.24 × 7.09 × 3.15 in), has a gently sloped 64 mm front and 8 tab-and-slot pieces.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 180 × 80 mm (10.24 × 7.09 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 900 × 272 mm
- Cut length
- 5.23 m
- Est. time, 10 W diode (3 mm)
- 17 min 26 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 16 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood thickness and cut a test tab to check that it slides into a slot without forcing.
- 02Cut all 8 parts from the 900 × 272 mm layout, or on two smaller sheets.
- 03Fit the back and sloped sides into the base, add the two long dividers, slot the short cross divider into the right column, then add the low front.
- 04Varnish or oil the wood and fill the four pockets with napkins, coasters, straws and toothpicks.
Four places, one footprint
Most table caddies give straws and toothpicks one shared slot, and the picks end up lost between the straws. Here the right-hand column is divided across by a short cross divider. The back pocket holds bent steel and clear glass straws upright, while the front pocket keeps a small glass of toothpicks where it is easy to reach. To the left of that column, a middle section fits a leaning stack of cork coasters, and the wide first section takes square paper napkins on edge.
The front wall stands 64 mm high, a little lower than the 80 mm back, so the side panels slope gently. It is a softer slope than on the deeper-cut caddies, which keeps tall napkins from flopping forward.
Cutting and building
Cutting time for the 3 mm file is about 17 min 26 s on a 10 W diode, about 7 min 16 s on a 40 W CO2 and about 3 min 29 s on a 100 W CO2. The layout is 900 × 272 mm; if that is wider than your bed, put the base, front and back on one sheet and the sides with all three dividers on a second.
Set the back and sides into the base, push in the two long dividers, then slide the short cross divider into the right-hand column before closing the front. The joints are snug enough to hold without glue, and a thin line of wood glue makes the organizer permanent.
Who buys it
Bar carts, outdoor kitchens and family barbecue tables all need straws and picks kept apart, which makes this layout an easy seller at summer markets. Sealed with exterior varnish, it survives a season on the patio.
Questions about this file
What is the small cross divider for?
It splits the right-hand column into a back pocket and a front pocket. Straws stand in the back and a cup of toothpicks or cocktail picks sits in the front.
Can I leave out the cross divider?
Yes, the box holds together without it, and the right column becomes one long slot for cutlery or straws.
Will reusable bent straws fit upright?
Yes, the back pocket is the full 80 mm tall and supports straws of normal length leaning against the back wall.
Is thin or thick plywood better for a straw and napkin organizer?
Use 3 or 4 mm birch for a light table piece. Choose 6 mm for a bar or patio where the organizer gets knocked about.
Can I scale it for a larger table?
Scale the outline, then set every slot back to your real plywood thickness. Skip that step and the straw corner joints end up sloppy or too tight.
Similar files



