VisualizationHinged Box SVG, Spice Box With Flip Lid Laser Cut File, Wooden Spice Chest DXF, Herb Sachet Box
This free laser-cut file builds a spice box with a flip-open lid that pivots at the back on pins cut into the plywood, and three sections inside. It measures 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in), has 8 plywood pieces joined with tabs and slots, and is supplied as SVG and DXF in separate versions for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 860 × 276 mm
- Cut length
- 6.26 m
- Est. time, 10 W diode (3 mm)
- 20 min 53 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 42 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the SVG or DXF for your plywood thickness and cut a test slot on an offcut first.
- 02Cut all eight parts, moving the base and lid to a second sheet if the 860 mm layout does not fit your bed.
- 03Assemble the base, back, front and both tall side panels, slide in the two dividers, then seat the lid on its pivot pins.
- 04Open and close the lid a few times, sand where it rubs, finish with wax oil and load the three sections.
Inside the box
Two dividers from front to back give three sections. The photo shows six small jars of herbs, paprika, peppercorns and chili flakes packed into the left section, single-serve spice sachets stacked in the middle and a row of garlic and herb packets on the right. With the lid down, the box reads as a small wooden chest on the counter, and nothing collects dust.
How the lid pivots
The two side panels are a little taller at the back, and the pivot is cut into them: small round pins hold the lid so it swings up and stays leaning back while you pick a jar. There are no metal parts to buy. Fit the lid last, after the walls and dividers are in place, and check that it clears the dividers as it closes; if it rubs, sand the top edge of the dividers rather than the lid.
Cutting plan and finishing
The 3 mm layout is 860 × 276 mm. For a smaller laser bed, put the base and lid on one sheet and the walls with both dividers on another. Times for the 3 mm file: about 20 min 53 s with a 10 W diode, about 8 min 42 s on a 40 W CO2 and about 4 min 11 s on a 100 W CO2. A 10 W diode needs one or two passes for 3 mm; plan on a stronger laser or several passes for 5 and 6 mm.
Glue the corners if you want, but keep glue well away from the pivot pins. A coat of hard wax oil protects the lid from steam. As a gift, engrave a herb wreath or a family name on the lid yourself and fill it with a starter set of spices.
Questions about this file
Does the hinged spice box need metal hinges?
No. The lid turns on pins cut into the plywood side panels, so the whole box comes from the sheet.
How far does the lid open?
It swings up and rests leaning back, as in the photo, which leaves all three sections open at once.
Can I engrave the lid?
Yes, the outside of the lid is a flat panel. Add your own engraving layer, such as a name or herb drawing, before cutting.
Which thickness keeps the pivot strongest?
The 4 or 5 mm versions give thicker pins that wear less with daily use. 3 mm works well for a lighter box opened now and then.
Can I make it deeper for tall jars?
Changing the height means changing the side panels, pivot and lid together, so keep the original proportions. If you do resize, keep slot widths equal to your material thickness.
Similar files



