VisualizationZiplock Bag Storage SVG, Kitchen Drawer Organizer With Side Pockets Laser File, Freezer Bag Bin DXF
A sloped kitchen bin with one wide bay for ziplock and freezer bags and a narrow right-hand column split into three pockets for clips and small tools. It is provided as SVG and DXF, with a separate file for each of 3, 4, 5 and 6 mm plywood, and measures 320 × 240 × 80 mm (12.60 × 9.45 × 3.15 in). Eight pieces form 4 compartments, the front drops to 48 mm, the parts join with tabs and slots, and the file is free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 240 × 80 mm (12.60 × 9.45 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,140 × 332 mm
- Cut length
- 6.12 m
- Est. time, 10 W diode (3 mm)
- 20 min 23 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 30 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the 3, 4, 5 or 6 mm version and cut one pocket divider on scrap to see how it seats in the long divider.
- 02Cut all eight pieces; if your bed is under about 1140 mm, nest them on two sheets.
- 03Set the sides and back on the base, push the long divider in, fit the two short cross dividers into the right column and finish with the low front.
- 04Sand, oil or lacquer, then stack bags in the wide bay and sort clips and tools into the three pockets.
Big bay plus a gadget column
One long divider runs front to back and splits the box unevenly: about 180 mm on the left for bags and wrap, and a narrower column of about 130 mm on the right. Two short cross dividers break that column into three pockets that climb toward the back wall. In the photo the wide bay takes three colors of zip bags laid flat with a cling film roll in front of them, while the pockets hold bag clips, a coil of rubber bands, and a spoon, whisk and spatula. Keep the bags you open most often at the front of the bay.
Choosing thickness and cutting
For a bin that mostly carries bags, 3 mm or 4 mm birch plywood is plenty. Thicker 5–6 mm sheet looks chunkier but takes more power: on a 10 W diode, plan several passes. The 3 mm file cuts in about 20 min 23 s on a 10 W diode, about 8 min 30 s on a 40 W CO2 and about 4 min 05 s on a 100 W CO2. The layout is about 1140 × 332 mm, so on a compact machine split it into two or three smaller jobs.
Start with the base and both sides, add the back, slide in the long divider, then fit the two cross dividers against it and set the 48 mm front last. It holds dry, and wood glue makes it permanent.
Selling tips
Photograph it filled with colorful bags, because buyers respond to the sorted look. Offer it as a single listing and as a bundle with a wrap tray, or engrave a family name on the front panel for a personalized housewarming gift.
Questions about this file
How wide is the main bay?
The long divider leaves roughly 180 mm on the left, enough for zip bags laid flat or standing on edge across the 240 mm depth.
Can I resize it for my drawer?
Change the outer size in your editor, but redraw or keep every slot at your actual plywood thickness so the tabs still lock.
Is MDF a good choice?
MDF cuts cleanly and takes paint well, but seal it carefully because raw MDF swells if it gets wet near the sink.
Should I glue the pockets?
The short cross dividers sit in slots in the long divider and the side wall. A tiny bead of glue stops them lifting when you pull clips out.
Can I engrave a name on it?
Nothing is engraved in the file, but the 320 mm front panel has room for a name or the word bags; add a raster layer before cutting.
Similar files
