VisualizationFood Bag Organizer SVG, Cling Wrap Roll Holder Laser File, Kitchen Gadget Tray DXF, Plastic Wrap Storage Box
A kitchen tray with one long rear lane for a cling film roll or a stack of food bags and four small front cups for clips, rubber bands and gadgets. It comes as SVG and DXF in separate versions for 3, 4, 5 and 6 mm plywood, measures 340 × 240 × 80 mm (13.39 × 9.45 × 3.15 in) and is cut from 9 pieces into 5 compartments, with sides sloping down to a 40 mm front. The wrap-lane tray joins with tabs and slots and costs nothing to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 240 × 80 mm (13.39 × 9.45 × 3.15 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,180 × 332 mm
- Cut length
- 6.57 m
- Est. time, 10 W diode (3 mm)
- 21 min 53 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 07 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the version for your sheet (3, 4, 5 or 6 mm) and test one short divider in its slot before cutting everything.
- 02Cut all nine parts, splitting the 1180 mm layout over two sheets if your bed is shorter.
- 03Build the shell from base, sides and back, fit the long cross divider, add the three cup dividers, then set the 40 mm front.
- 04Sand and oil the tray, lay the wrap roll in the back lane and sort clips and gadgets into the four cups.
One long lane, four cups
A single cross divider runs the full 340 mm width and leaves a long lane against the back wall. That lane is the reason to pick this design: a roll of plastic wrap lies in it horizontally, and a flat stack of freezer bags slides in beside it. In front of the cross divider, three short dividers make four cups of roughly 80 mm each. We used them for sealing clips, a tangle of rubber bands, measuring spoons with a mini spatula, and a peeler with a tea strainer. The cups sit lower than the back lane, so nothing hides behind them.
Cutting notes
Nine flat parts come out of the file: front, back, two sloped sides, base, the long cross divider and three small dividers. The 3 mm layout is about 1180 × 332 mm; on a 400 mm class bed, put the base on one sheet and the walls and dividers on another. For the 3 mm file a 10 W diode needs about 21 min 53 s, a 40 W CO2 about 9 min 07 s and a 100 W CO2 about 4 min 23 s. If you go for 5 or 6 mm, plan on a CO2 tube or several diode passes.
Assemble the shell first, then drop in the long cross divider and finally slot the three small dividers onto it. Glue is not required; add a little wood glue at the corners if the tray will be lifted often.
Finishing and gift ideas
Round over the edges with fine sandpaper and give the box a coat of oil or clear lacquer, since wrap and bags live near the sink. Fill it with a roll of film, a pack of bags and a set of clips and you have a ready housewarming gift. In a shop it also works as an add-on listing next to a matching spice tray.
Questions about this file
Does a roll of cling film fit in the back lane?
The lane spans the whole inside width of the 340 mm box, so a roll of plastic wrap of the usual 30 cm width lies in it lengthwise.
Can I scale this tray to fit a deeper drawer?
Yes, but change only the outer dimensions and keep the slot width equal to your real plywood thickness. A plain percentage scale makes the slots too wide or too tight.
Will it work in MDF or acrylic?
MDF cuts the same way and paints well. Acrylic works for a clear version, but cut a test slot first because acrylic thickness varies and the joints need a dab of acrylic cement.
Is 3 mm plywood strong enough for this one?
For bags, clips and gadgets 3 mm is fine and keeps the cut short. Pick 4 mm if the tray will be carried around full.
Can I label the four cups?
The file has cut lines only, but you can add a small engraving layer on the front panel above each cup, for example clips or bands, before cutting.
Similar files
