Upright Ziplock Bag Holder – 5 Slots, Free SVG/DXF

Ziplock Bag Holder SVG, Upright 5 Slot Kitchen Organizer Laser Cut File, Countertop Bag Sorter DXF

A narrow, tall countertop organizer with five upright slots that keep zip bags, clips, wrap rolls and utensils standing on edge. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box is 300 × 180 × 100 mm (11.81 × 7.09 × 3.94 in), cut from 9 pieces, with four full-height dividers making 5 compartments. The sides slope to a 60 mm front, it assembles with tabs and slots, and it is free to download.

Author

DXF World · 240 files

Formats

SVG, DXF

Outer size (W × D × H)

300 × 180 × 100 mm (11.81 × 7.09 × 3.94 in)

Parts

Material thickness

3, 4, 5 or 6 mm plywood (a file for each)

Layout size (3 mm file)

1,044 × 292 mm

Cut length

6.59 m

Est. time, 10 W diode (3 mm)

21 min 59 s

Est. time, 40 W CO2 (3 mm)

9 min 10 s

Layers

CUT only, no engraving

Free account required to download

How to make it

01Choose the SVG or DXF for your plywood thickness and cut one divider plus a test slot to check the fit.

02Cut the nine pieces; the four dividers are identical, so you can nest them tightly together.

03Assemble base, sides and back, then slide the four dividers down into their slots and add the 60 mm front.

04Sand and seal, then stand bags on edge in the slots with clips and rolls beside them.

Built for standing things on edge

At 100 mm tall and only 180 mm deep, this is the tallest and most compact holder in the bag series. Four dividers run the full depth, making five slots of roughly 55 mm each. That width is the point: zip bags stand upright like papers in a file box, clips line up side by side, and two short rolls of cling film sit without tipping. In the photo the slots hold, left to right, zip bags, colored clips, rubber bands, wrap rolls, and a spoon, whisk and spatula. Because the front is 60 mm high, tall items stay supported while still being easy to pull out.

Cutting tips

The layout is about 1044 × 292 mm for 3 mm. A 10 W diode cuts the 3 mm file in about 21 min 59 s, a 40 W CO2 in about 9 min 10 s and a 100 W CO2 in about 4 min 24 s. All four dividers are identical, so if one comes out scorched you can recut it alone. On a small bed, put the base and back on one sheet and the dividers and sides on another. 5 and 6 mm plywood needs a CO2 laser or several slow diode passes.

Fit the sides to the base, add the back, slide the four dividers in from the top, then finish with the front wall. A drop of glue on each divider tab keeps them from lifting when you grab a bag.

Ideas for selling

A slim footprint suits small kitchens and pantry shelves, which is a good angle for listings. Offer it in natural wood and in a painted color, or as a matched pair with a snack caddy. Sand the slot edges and finish with clear lacquer so it wipes clean.

Questions about this file

How wide is each slot?

Five slots share the 300 mm width, so each is about 53 to 56 mm wide depending on plywood thickness: room for a stack of zip bags on edge or two rolls of wrap.

Can I make it taller for gallon bags?

You can stretch the height in your editor, but keep the slot and tab widths matched to your plywood; do not scale the whole file uniformly.

Is it stable on a counter?

The 180 mm depth and full base keep it steady when loaded. On a slippery surface, add small felt or silicone feet.

Does MDF work for this holder?

MDF works and paints evenly, but seal it well, as raw MDF swells when it gets wet near a sink.

Will 3 mm dividers bend under a stack of bags?

At 180 mm long they stay straight with bags and clips; choose 4 mm if you plan to pack the slots tightly.