Visualization9 Compartment Snack Organizer SVG, Square Snack Tray Laser Cut File, Snack Variety Box, Party Snack Display DXF
A square snack organizer with 9 compartments in a three-by-three grid whose rows step up toward the back. It comes as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood, measures 300 × 300 × 90 mm (11.81 × 11.81 × 3.54 in), and is cut from 13 pieces, the most in the snack set. The sides slope to a 50 mm front, the parts join with tabs and slots, and it is a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 300 × 90 mm (11.81 × 11.81 × 3.54 in)
- Parts
- 13
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,220 × 483 mm
- Cut length
- 9.18 m
- Est. time, 10 W diode (3 mm)
- 30 min 36 s
- Est. time, 40 W CO2 (3 mm)
- 12 min 45 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the 3, 4, 5 or 6 mm file and cut a single cross divider and slot from scrap to check the fit.
- 02Cut all thirteen pieces over several sheets if needed, and pencil-mark each cross divider with its column.
- 03Build base, sides and back, insert the two long dividers, add the six cross dividers one column at a time, and fit the 50 mm front.
- 04Sand every cell edge, finish with oil or lacquer, and fill the nine cells with different snacks.
Nine cells in three steps
Two long dividers cut the square into three columns, and each column gets two short cross dividers, about 63 mm and 77 mm tall. The result is a three-by-three grid where the back row sits highest and the front row lowest. The photo shows granola bars, mixed nuts and crackers in the back row; dried apricots, cranberries and seed bars in the middle; and chocolate bars, cracker squares and fruit snacks in front. Nine choices make it a natural variety box for guests or a party table.
Planning the cut
Thirteen parts, a 300 × 300 mm square base and a 3 mm layout of about 1220 × 483 mm make this the biggest job in the set. A 10 W diode needs about 30 min 36 s for the 3 mm file, a 40 W CO2 about 12 min 45 s and a 100 W CO2 about 6 min 07 s. On a 400 mm bed, cut the base alone, then the four walls, then the dividers. The six cross dividers come in two heights and three slightly different lengths, so mark them with a pencil as they come off the bed. For 5 or 6 mm plywood, use a CO2 or plan several passes on a diode.
Assemble the shell, slide in both long dividers, then add the cross dividers column by column, and close with the front. It holds dry; glue at the cross dividers keeps the grid tight.
Finishing and gift ideas
Sand the cell edges and finish with oil or lacquer. Filled with nine kinds of snack, it is a ready-made gift for teachers, coworkers or holiday hosts. Holiday rental hosts like square snack trays for welcome tables, and an engraved message on the front adds value to gift orders.
Questions about this file
What size are the nine cells?
Each column is roughly 100 mm wide and the rows split the 300 mm depth into three, so single-serve packs, bars and small cracker sleeves fit.
Can I resize the grid?
Change the square size in your editor, but keep slot widths matched to your plywood; scaling the slots with the outline makes the joints fail.
Which thickness should I pick?
3 mm leaves the most room in nine small cells and cuts fastest; 4 mm is sturdier for a box that gets carried to a party.
Can I use acrylic for a clear display?
Clear acrylic looks good as a snack display; test one joint first and glue the grid with acrylic cement.
Why mark the cross dividers?
They come in two heights and three slightly different lengths, so labelling them by column saves trial and error during assembly.
Similar files
